Quantum Scalar 10K Скачать руководство пользователя страница 64

Страница: 64 / 324

3-8

System Description

6-00058-05 Rev A

Figure 3-2

Main Screen

Shutting Down the Scalar 10K

The Scalar 10K may be shut down normally or by the
Emergency Shutdown method.

Use the method described in

Emergency Shutdown

in cases

of emergency only.

Normal Shutdown

Proceed as follows to shutdown the Scalar 10K:

With the RMU installed, power up must be delayed by one
minute after a power down condition to allow the RMU to
properly reset.

Step 1

If necessary, use the

button to return to the

Main Menu. The cursor defaults to the Mode
selection. Press the

button. From the Mode

screen, use the

button to select the Shutdown

mode.

Press the

button.

The Accessor completes the current task and returns to
the home position. The reboot message appears. See
Figure 3-3.

Figure 3-3

Reboot Screen

MAIN SCREEN

MM/DD/YY

Idle

Online.........Ready

HH/MM/SS

Warning

Caution

The library may now

be rebooted.

Содержание Scalar 10K





































































































































































































































































































































Результаты поиска

Содержание Scalar 10K

Отзывы:

Похожие инструкции для Scalar 10K

Бренды по названию

Популярные бренды

Quantum Scalar 10K, Руководство пользователя

Результаты поиска

Содержание Scalar 10K

Отзывы:

Похожие инструкции для Scalar 10K

Бренды по названию

Популярные бренды