Qorvo PAC25140 Скачать руководство пользователя страница 25

Страница: 25 / 77

PAC25140 Users Guide Preview

No portion of this

document may be reproduced or reused in any form without Qorvo’s prior written consent

www.qorvo.com

25 of 77

BIT

NAME

ACCESS

RESET

DESCRIPTION

HWRSTAT

0x0

Hardware Reset Status. Bit is set on hardware reset and is
cleared when written to 1b.

0b: No hardware reset

1b: Hardware reset

SRST

0x0

Soft Reset Event. Bit is set on software reset event and is
cleared when written to 1b.

0b: No software reset

1b: Software reset

WDTRSTAT

0x0

Watchdog Timer Reset Status. When enabled, this bit is set
on Watchdog Timer Reset and cleared when written to 1b.

0b: No WDT reset

1b: WDT Reset

RFU

0x0

Reserved

VPLOW

0x0

Real-time VP Low Status.

0b: No VP low

1b: VP low

VPLOW_LATCH

0x0

Latched VP Low Status. During VP low condition, this bit is
set and the nIRQ signal is asserted. To clear this bit, write to
1b.

0b: No latched VP low

1b: Latched VP low

PBSTAT

0x0

Real-time Push-button Status.

0b: Push-button not active

1b: push-button active

PBSTAT_LATCH

0x0

Latched  Push-button  Status.  This  bit  is  set  in  normal
operation  as  long  as  the  push  button  is  enabled  and  on  for
more  than  the  deglitch  time,  if  not  masked.  When  this  bit  is
set, it will assert the nIRQ signal.

0b: Latched push-button not active

1b: Latched push-button active

Содержание PAC25140














































































Результаты поиска

Содержание PAC25140

Отзывы:

Похожие инструкции для PAC25140

Бренды по названию

Популярные бренды

Qorvo PAC25140, Руководство пользователя

Результаты поиска

Содержание PAC25140

Отзывы:

Похожие инструкции для PAC25140

Бренды по названию

Популярные бренды