Speedkid
Speedkid
Subject to change without notice. – 12 | 2020 –
59
58
– 12 | 2020 – Subject to change without notice.
The table below shows the main settings that you must make for particular components for the
respective mode:
Component
Status of the components in mode
Trailer
Buggy
Walker
Buggy-wheel
must be completely
removed
fitted
(freely rotating)
fitted
(fixed)
Tow bar
directed forwards
(pay attention to tow
bar load!)
directed backwards
directed backwards
Pennant
must be mounted
recommended
recommended
Push handle
10 - 15 cm
above the roof
of the cabin
comfortable height
comfortable height
Hand strap on the
push handle
–
wrapped around a
wrist
wrapped around a
wrist
5-point safety harness
must be fastened
must be fastened
must be fastened
Rear light
must work in poor
visibility or darkness
(observe StVZO)
recommended in
poor visibility or
darkness
recommended in
poor visibility or
darkness
Bicycle
the correct coupler
must be installed
–
–
Danger!
Before every journey, make sure that necessary adjustments have been made
for the particular mode. For details of this, see the instructions in the following
sections.
Adjusting the buggy wheel
You must make the following settings, depending on the mode.
Removing the buggy wheel (Trailer mode)
The buggy wheel must not be fitted in Trailer mode, because in certain riding situations it can
make contact and cause serious accidents.
»
Slightly lift the cabin at the front.
»
Push the release button at the wheel mount and remove the buggy wheel completely.
Tip!
Carry the buggy wheel e.g. in the storage space in order to allow you to use the
flexibly at your destination. Instructions for re-mounting it can be found in the
chapter
„Installing the buggy wheel“ on page 53
.
Setting the wheel so that it turns freely (Buggy mode)
It must be possible for the wheel to move freely through 360 ° in order to manoeuvre in Buggy mode.
»
Push up the mode switch to release the wheel.
Securing the wheel (Walker mode)
In Walker mode, the wheel must not be at an angle to the direction of travel. You must lock the
wheel to run straight ahead in order to prevent abrupt blocking.
»
Push down the mode switch to make sure the wheel is running straight.
»
Turn the positioned wheel backwards until it engages audibly.
»
The wheel must not be subjected to any resistance
Insert tow bar
The tow bar can either be brought forward into the attachment position or carried along backwards
in the standby position: Pay attention also to the instructions in the chapter
„Mounting the tow bar“
on page 54
.
Danger!
Wrap the retaining strap of the tow bar around the tow bar several times to ensure
it does not hang down in the standby position. Otherwise it could become trapped
on obstacles.
Using the pennant
The pennant must be attached in Trailer mode, see
„Inserting the pennant“ on page 53
. For safety
reasons, we also recommend this for the other modes.
Attaching the hand strap
In Buggy and Walker mode, the hand strap secured to the push handle must be attached to
your wrist during every journey.
Putting on the 5-point safety harness
In every mode, the 5-point safety harnesses must be properly adjusted and every child must be
fastened in, see
„Middle sitting position (Speedkid2)“ on page 61
.
Securing the load
Loading the storage space
»
To open, grab the storage cover with both hands.
»
Pull the elastic band of the storage cover until it can be opened upwards over the frame.
»
Place larger items such as bags, toys or jackets in the storage. If necessary, use the extra
cup holder.
»
To close, stretch the storage cover over the frame again.
Using the beverage holders
»
Put the children’s drinking bottles into the beverage holders in the cabin’s foot space.
Danger!
When loading, pay attention to the total permissible weight and the weight limits,
see
„Performance limits“ on page 42
.
Utilisation
Utilisation
