manualshive.com logo in svg

PVI Industries TEMPTRAC, Руководство пользователя, Страница: 24 / 30

Поделиться
Скачать
PVI Industries TEMPTRAC Скачать руководство пользователя страница 24

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST 

Page 24 of 30 

PV7069-T   03/17 
Part number 129209 

ALL POINTS INCLUDING ADVANCE: 

Alarm_Nn1 

Read Only 

Maintenance Alarm for output #1 

MODBUS 

Holding Register 

3328 

43329:13 

BACNET 

Alarm_Nn1 

332963 

 

LONWORKS 

nvoAlarm_Nn1_# 

 

 

Maintenance Alarm. This is enabled when the time on ou1 is greater than the value in oP1. Flashes ‘Nn1’ on 
TempTrac display. Bit #13 of Alarms. In BACNET and LONWORKS, this is broken out into a state logic point. 
For MODBUS ALARMS && 0x2000 = 0x2000 Alarm is active. = 0x0000 Alarm is not active. 
 

Alarm_Nn2 

Read Only 

Maintenance Alarm for output #2 

MODBUS 

Holding Register 

3328 

43329:14 

BACNET 

Alarm_Nn2 

332963 

 

LONWORKS 

nvoAlarm_Nn2_# 

 

 

Maintenance Alarm. This is enabled when the time on ou2 is greater than the value in oP2. Flashes ‘Nn2’ on 
TempTrac display. Bit #14 of Alarms. In BACNET and LONWORKS, this is broken out into a state logic point. 
For MODBUS ALARMS && 0x4000 = 0x4000 Alarm is active. = 0x0000 Alarm is not active. 
 

Alarm_Nn3 

Read Only 

Maintenance Alarm for output #3 

MODBUS 

Holding Register 

3328 

43329:15 

BACNET 

Alarm_Nn3 

332963 

 

LONWORKS 

nvoAlarm_Nn3_# 

 

 

Maintenance Alarm. This is enabled when the time on ou3 is greater 

than the value in oP3. Flashes ‘Nn3’ on 

TempTrac display. Bit #15 of Alarms. In BACNET and LONWORKS, this is broken out into a state logic point. 
For MODBUS ALARMS && 0x8000 = 0x8000 Alarm is active. = 0x0000 Alarm is not active. 
 

Com Status 

Read Only 

Communication Status bit 

MODBUS 

Input Register 

NA 

NA 

BACNET 

Gateway_TT_Com_OK 

200 

 

LONWORKS 

nvoGwyTTCmOK_# 

 

 

NOTE: This point is not generated by the heater; it is generated internally by the gateway. It is a status of the 
communication connection between the gateway and the heater. If active (GOOD), the gateway is talking to the 
heater. If inactive (NOT_PRESENT) then the gateway does not have good communication with the heater. This 
point may take up to 3 minutes to register properly after communication is established or interrupted. If this 
value if reading NOT_PRESENT, then no all over values are suspect, as the device is not communicating. 
Generally the Gateway will hold the last value received. The only way to ensure you have the current values 
from the heater is to verify this point is ACTIVE as well. 

 
 

Содержание TEMPTRAC































Отзывы:

Нет отзывов