manualshive.com logo in svg

PVI Industries TEMPTRAC, Руководство пользователя, Страница: 18 / 30

Поделиться
Скачать
PVI Industries TEMPTRAC Скачать руководство пользователя страница 18

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST 

Page 18 of 30 

PV7069-T   03/17 
Part number 129209 

TYPICAL POINTS: 

Alarm_AL3 

Read Only 

Status of digital input #3 Alarm 

MODBUS 

Holding Register 

3328 

43329:12 

BACNET 

Alarm_AL3 

332962 

 

LONWORKS 

nvoAlarm_AL3_# 

 

 

Digital Input #3 alarm. On some products, this is a general failure to operate alarm. See product specific 
information. This is Bit 12 of the ALARM STATUS ALL word. 

Flashes ‘AL3’ or ‘HP’ on TempTrac display. In 

BACNET and LONWORKS, this is broken out into a state logic point. 
For MODBUS ALARMS && 0x1000 = 0x1000 Alarm is active. = 0x0000 Alarm is not active. 
 

Com Status 

Read Only 

Communication Status bit 

MODBUS 

Input Register 

NA 

NA 

BACNET 

Gateway_TT_Com_OK 

200 

 

LONWORKS 

nvoGwyTTCmOK_# 

 

 

NOTE: This point is not generated by the heater; it is generated internally by the gateway. It is a status of the 
communication connection between the gateway and the heater. If active (GOOD), the gateway is talking to the 
heater. If inactive (NOT_PRESENT) then the gateway does not have good communication with the heater. This 
point may take up to 3 minutes to register properly after communication is established or interrupted. If this 
value if reading NOT_PRESENT, then no all over values are suspect, as the device is not communicating. 
Generally the Gateway will hold the last value received. The only way to ensure you have the current values 
from the heater is to verify this point is ACTIVE as well. 

 
 

ALL POINTS INCLUDING ADVANCED: 

Points  listed  below  that  are  not  in  the  TYPICAL  POINTS  are  provided  for  advanced  interface  and  for 
custom applications.  Contact factory for additional information.  
 

ALL POINTS INCLUDING ADVANCE: 

Control_CNT 

Write 

Enable Heater 257=on 1 = off 

MODBUS 

Holding Register 

1280 

41281 

BACNET 

Enable 

128100 

 

LONWORKS 

nvoCtrl_CNT_# 

 

 

This can be used to prevent the heater from heating via communication. 257 or 0X0101 = on, 1 or 0x0000 = off 
The resister cannot be read. The register should only be written to with the values 257 and 1, as it has other 
undocumented functions. 
 

Setpoint_St1 

Read/Write 

System Setpoint 

MODBUS 

Holding Register 

768 

40769 

BACNET 

Setpoint_St1 

76900 

Deg-F  

LONWORKS 

nvoSP_St1_# 

nviSP_St1_# 

Deg_F 

This is the setpoint for the heater. 
 

Setpoint_St1 C 

Read/Write 

System Setpoint 

MODBUS 

 

 

 

BACNET 

Setpoint_St1_C 

76900 

Deg-C 

LONWORKS 

 

 

 

Special BACNET point that converts the Setpoint value to degrees C in the gateway. Not available in 
LONWORKS or MODBUS. 
 

Содержание TEMPTRAC































Отзывы:

Нет отзывов