manualshive.com logo in svg

PVI Industries TEMPTRAC, Руководство пользователя, Страница: 13 / 30

Поделиться
Скачать
PVI Industries TEMPTRAC Скачать руководство пользователя страница 13

TEMPTRAC INTERFACE GUIDE, GATEWAY SETUP AND POINTS LIST 

Page 13 of 30 

PV7069-T   03/17 
Part number 129209 

Centauri Boiler, Centauri Plus Boiler, VT3 Boiler: 

Model Numbers: All Centauri, Centauri Plus and VT3 Boilers 
 

Probe 1:

 This temperature is displayed in yellow in the lower section of the display. 

With SSBCO option, this probe is located in the top of the boiler. Without this option, 
the probe is shipped uninstalled and should be installed in the BHWR piping to read 
the temperature of the water entering the boiler. 

Probe 2

: This temperature is displayed in red in the upper section of the display. 

With SSBCO option, this probe is shipped uninstalled and is intended to be installed 
in  the field  in 

the boiler’s HWR piping. Without the SSBCO option, this probe is 

installed in the top of the boiler providing the outlet water temperature. 

Probe 3

: Is an Auxiliary probe that can be used for outdoor temperature or other 

temperature readings. This is optional and not standard. 

Alarm_AL3

: Alarm on any failure 

Burner_Relay1

: Burner 

Relay2

: Not used 

Relay3

: Isolation Valve control when the OnTrac boiler management system is controlling. 

Modulation Rate

: Modulation rate, Low fire = 0, High Fire = 100 

 

Discrete connections: 
Ext  Enable:

  Terminals  R1 

–  R2,  Jumper  to  enable.  Heater  ships  with  jumper  on  this.  An  external 

enable/disable can be attached to this. (Recommend relay at boiler, min 10A at 24VAC.) 

Remote Equipment

: P1 & P2, this is a contact that is driven any time a call for heat is present. Note this 

is only provided if the Remote Equipment or Louver options are present. 

Alarm

: A1 & A2 provide a 3 min alarm signal that is present after a failure to ignite burner for 4 minutes. 

This output will be active for 3 minute and then the communication alarm will become active dropping the 
call for heat and dropping this signal. It is possible to get this alarm and the alarm condition that caused 
this alarm can be corrected before the 3 minutes, removing the alarm and not having a lockout or alarm 
condition over communication. (3 min signal of alarm condition and potential lockout.) 
 

Содержание TEMPTRAC































Отзывы:

Нет отзывов