PureTools PT-PMS-42S Скачать руководство пользователя страница 49

Страница: 49 / 68

User Manual

PT-PMS-42S

Command

Description

Command Example and
Feedback



[PARAM1]=1~10

[PARAM1]

Resolution

4K@60HZ 4:4:4

4K@30Hz 4:4:4

1920X1200@60Hz

1080P@60Hz

1080P@50Hz

1600x1200@60Hz

1360x768@60Hz

1024x768@60Hz

720P@60Hz

720P@50Hz

@OUTPUT_RES 4k@60 TO 01

#GET_OUTPUT_RES
[PARAM]

Get the video resolution of output
[PARAM].
[PARAM]=01~02, ALL

#GET_OUTPUT_RES 01

@OUTPUT RES 1080@60 TO
01

8.2.6

EDID Management

Command

Description

Command Example and
Feedback

#SET_EDID_MODE
CAL:[PARAM1] TO
[PARAM2]

The HDMI input [PARAM2] invoke
built-in EDID [PARAM1].

[PARAM1]=01~03 (EDID)

[PARAM2]=01~03 (1.HDMI IN~3.HDMI
IN)

[PARAM1]

EDID

1080P@60Hz 2CH

4K@30Hz 4:4:4 2CH

4K@60Hz 4:4:4 2CH

#SET_EDID_MODE CAL:01 TO
02

@EDID_MODE CAL:01 TO 02

#SET_EDID_MODE LRN:
[PARAM1] TO [PARAM2]

Set the EDID data of output [PARAM1]
to input [PARAM2].

#SET_EDID_MODE LRN:02 TO
01

Содержание PT-PMS-42S




































































Результаты поиска

Содержание PT-PMS-42S

Отзывы:

Похожие инструкции для PT-PMS-42S

Бренды по названию

Популярные бренды

PureTools PT-PMS-42S, Руководство пользователя

Результаты поиска

Содержание PT-PMS-42S

Отзывы:

Похожие инструкции для PT-PMS-42S

Бренды по названию

Популярные бренды