PureTools PT-PMS-42S Скачать руководство пользователя страница 9

Страница: 9 / 68

User Manual

PT-PMS-42S

Specification

2.1

Matrix Switcher

Video Input

Video Input

(3) HDMI, (1) USB-C

Video Input Connector

(3) Type-A female HDMI, (1) Type-C USB 3.0

Video input Video
Resolution

HDMI: Up to 4Kx2K@60Hz 4:4:4 8bit

USB-C: Up to 4Kx2K@30Hz

Video Output

Video Output

(1) HDMI, (1) HDBaseT with (1) HDMI

loop

Video Output Connector

(2) Type-A Female HDMI, (1) RJ45

Video output Video
Resolution

HDMI: Up to 4Kx2K@60Hz 4:4:4, supports 4K to 1080P down-scaling.

HDBaseT: Up to 4Kx2K@60Hz 4:4:4

HDMI Version

Up to 2.0

HDCP Version

Up to 2.2

Audio Input

Audio Input

(1) External balanced audio (L+R) for

1.HDMI

input port,

(1) Balanced MIX audio, (1) MIC audio,

Audio Input Connector

(2) 5-pin terminal blocks, (1) 3-pin terminal block

HDMI Input Audio Stream

PCM 7.1 audio, Dolby Atmos® , Dolby® TrueHD, Dolby Digital® Plus,
DTS:X™, and DTS-HD® Master Audio™ pass-through.

Frequency Response

20Hz~20KHz, ±3dB

Max Input Level

2.0Vrms±0.5dB. 2V=16dB headroom above-10dBV (316mV) nominal
consumer line level signal.

L-R Level Deviation

<0.3dB, 1KHz sine at 0dBFS level (or max level before clipping).

Input Impedance

>10KΩ

Audio Output

Audio Output

(1) Digital SPDIF audio, (1) Balanced audio (L+R)

Audio Output Connector

(1) Toslink connectors, (1) 5-pin terminal block

HDMI Output Audio Stream

PCM 2.0

SPDIF/Stereo Output Audio PCM 2.0

Содержание PT-PMS-42S




































































Результаты поиска

Содержание PT-PMS-42S

Отзывы:

Похожие инструкции для PT-PMS-42S

Бренды по названию

Популярные бренды

PureTools PT-PMS-42S, Руководство пользователя

Результаты поиска

Содержание PT-PMS-42S

Отзывы:

Похожие инструкции для PT-PMS-42S

Бренды по названию

Популярные бренды