PureTools PT-PMS-42S Скачать руководство пользователя страница 13

Страница: 13 / 68

User Manual

PT-PMS-42S

Panel Description

3.1

Matrix Switcher Front Panel

①

Power LED:

The LED illuminates red when the device is powered on.

②

SOURCE:

Total five buttons with blue backlight.



1.HDMI input selector / Left Key for On Screen Display control (OSD).



2.HDMI input selector / Right Key for OSD.



3.HDMI input selector / Up Key for OSD.



4.USB-C input selector / Down Key for OSD.



Auto switching mode selector. Press this to enter or exit auto switching mode.
/ Press and hold it at least 2 seconds to enable OSD menu.

③

OUTPUTS:

Two buttons with blue backlight.



1.HDMI output selector.



2.HDBT output selector.

④

RESOLUTION:

Two

output video resolution selectors.

Press the

1.HDMI

2.HDBT

button repeatedly to cycle through the four video resolutions. A series of four
LEDs, one of which illuminates blue to indicate which resolution is selected.

⑤

VOLUME:



Press the volume knob in to toggle among

MIX

MIC

and

AUDIO OUT

audio

control, and the corresponding LED will illuminate blue.



Rotate the knob to increase or decrease the volume of the selected audio.



Press and hold the knob at least three seconds to mute the selected audio.
Rotate the knob to unmute.

1. HDMI

2. HDMI

3. HDMI

SOURCE

OUTPUTS

RESOLUTION

VOLUME

PT-PMS-42S

Presentation Matrix

Содержание PT-PMS-42S




































































Результаты поиска

Содержание PT-PMS-42S

Отзывы:

Похожие инструкции для PT-PMS-42S

Бренды по названию

Популярные бренды

PureTools PT-PMS-42S, Руководство пользователя

Результаты поиска

Содержание PT-PMS-42S

Отзывы:

Похожие инструкции для PT-PMS-42S

Бренды по названию

Популярные бренды