PureTools PT-PMS-42S Скачать руководство пользователя страница 47

Страница: 47 / 68

User Manual

PT-PMS-42S

Command

Description

Command Example and
Feedback

01=HDMI output audio
02=HDBT output audio
03=MIX audio
04=MIC audio
05=L+R output audio

[PARAM2]=0~60

@VOL HDMI 60

#GET_VOL [PARAM]

Get the audio volume of output
[PARAM].
[PARAM]=

HDMI, HDBT, ALL.

#GET_VOL HDMI
#GET_VOL ALL

@VOL HDMI 60
@VOL HDBT 60
@VOL MIX 60
@VOL MIC 30
@VOL L+R 30

#SET_AUDIO_EMBEDDED
ON

Select the external balanced audio
(5-pin) to be embed in 1.HDMI input.

@AUDIO_EMBEDDED ON

#SET_AUDIO_EMBEDDED
OFF

Select the internal HDMI audio stream
of source device for 1.HDMI input.

@AUDIO_EMBEDDED OFF

#GET_AUDIO_EMBEDDED
01

Get the audio source of 1.HDMI input.

@AUDIO_EMBEDDED ON
@AUDIO_EMBEDDED OFF

#SET_AUDIO_MIX
[PARAM1] [PARAM2]

Enable/disable the output [PARAM1]
audio to mix with MIX audio.
[PARAM1]=01~02, ALL
01=HDMI Output
02=HDBT Output

ALL=All outputs
[PARAM2]=ON/OFF

#SET_AUDIO_MIX 01 ON
#SET_AUDIO_MIX ALL ON

@AUDIO_MIX 01 ON
@AUDIO_MIX 01 OFF
@AUDIO_MIX ALL OFF
@AUDIO_MIX ALL ON

#GET_AUDIO_MIX
[PARAM]

Get the MIX audio status of output
[PARAM].
[PARAM]=01~02, ALL
01=HDMI Output
02=HDBT Output
ALL=All outputs

#GET_AUDIO_MIX 01
#GET_AUDIO_MIX ALL

@AUDIO_MIX 01 ON
@AUDIO_MIX 02 OFF

Содержание PT-PMS-42S




































































Результаты поиска

Содержание PT-PMS-42S

Отзывы:

Похожие инструкции для PT-PMS-42S

Бренды по названию

Популярные бренды

PureTools PT-PMS-42S, Руководство пользователя

Результаты поиска

Содержание PT-PMS-42S

Отзывы:

Похожие инструкции для PT-PMS-42S

Бренды по названию

Популярные бренды