If your cable box has its own remote to change channels,
you will probably be able to program the TV’s remote to
control both the TV and the cable box.
The TV’s remote is designed to control several brands of
cable boxes. To program the remote, just press
CABLE
,
then
ID
,
then the two-digit code number for your brand of cable
box. Refer to the chart below to find the code number for
your cable box. Press the
OFF
/
ON
button next to confirm
operation. You may need to try each of the code numbers
listed until you find the one that works.
4
Press OFF/ON
to test.
3 Press two number
b u t t o n s
(See list below.)
-1 Press
CABLE
2
Press IO
08
Eastern International
02
General Instrument
36
Hamlin
12, 13, 34
Hitachi
Jerrold
36
MACOM
Magnavox
28.29, 32,
NSC
09
01. 16. 38
Oak Sigma
1 6
Panasonic
Philips
32,
Pioneer
18.20
Randtek
R C A
Regal
27
02
Scientific Atlantic
03.22
Svlvania
1 1
Teknika
Texscan
Tocom
06
10.11
17.21
Unika
31
After the TV’s remote is programmed, you will be able to
turn on the cable box by pressing
CABLE
then
OFF
/
ON
.
You
can change channels on the cable box by pressing the
CHANNEL
buttons whenever the remote is in the “cable
mode?. To put the remote in the “cable mode”, press the
CABLE
button. Press the button to put the remote back
into the “TV mode” so the remote buttons will control the
TV again.
Programming Remote To Control Cable Box
with master remote control only
Refer to the chart at the left to find the code number that
corresponds to the brand name of your cable box. Keep
this number in mind. If more than one number is listed,
you may need to try each one separately until you find the
one that works.
Press
C A B L E
button on remote.
Press
I D
button on remote.
Press two number buttons (first one, then the other)
to enter
the code number for your brand of cable box.
Note: You must press the two number buttons within three seconds
of pressing the
ID
button.
Point the remote at the cable box and press the
OFF
/
ON
button
to test the code number.
l
If the right number was entered, the cable box should turn
on.
Pressing the
C H A N N E L
buttons should then also change
channels on the cable box.
l
If the cable box does not react to the remote (or if the remote
turns on the cable box but does not change channels), repeat
steps 1 through 5 with another code number.
Operating Notes:
After the remote control is programmed, it will
on the cable box whenever you press
CABLE
and then
OFF
/
ON
.
To
off the cable box, press
CABLE
,
then
OFF
/
ON
.
To change channels on the cable box, press
CABLE
then
CHANNEL
up or down.
After you program the remote control, you can use the
Setup
function on the
SETUP
menu to automatically turn on the cable
box and tune the TV to the correct channel for the cable box when
you
press the
CABLE
button.
Details are on page 43.
Zenith
14.42
_
_
Note:
Refer to the information sheet packed with your remote control
for the latest list of brand names and code numbers. Because this list is
constantly growing, the information sheet packed with your remote
control may be a later version of this list and contain additional brands
and/or code numbers.
Содержание PS52682
Страница 65: ...I I I I I I I I I I t 1 I I I I 1 II 1 I 1 ...
Страница 81: ......
Страница 85: ......
Страница 86: ......
