PRONAR ZKP350 Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 60

PRONAR ZKP350 Скачать руководство пользователя страница 45

4.13

into windrow. Allowable revolution speed of articulated telescopic shaft is 540 revs/min

however recommended speed is about 450 revs/min. With a very dry swath it is

recommended that PTO shaft speed should be reduced even further.

IMPORTANT!

Do NOT start windrower with PTO revs speed higher than 540 revs/min.

The revolution speed of the shaft and the speed of travel depend on several factors, including

size of swath, degree of moisture, length of swath, type of ground, therefore the selection of

appropriate working parameters rests on the person operating the windrower. During

machine operation the linkage system shall be set in position regulation work mode.

DANGER

Before engaging drive to articulated telescopic shaft make sure that there are no
bystanders, especially children, near the windrower. Maintain proper visibility of

machine during work
Other persons should be at a safe distance from the windrower during work because of

the danger that objects may be thrown (stones, branches from beneath raking fingers.

Raking the swath in order to form it into windrows should be conducted in a system of smaller

areas. During turning or reversing, articulated telescopic shaft should be disengaged and

windrower raised. Width of windrow should be somewhat less that baler intake pickup – if

swath shall be baled.

4.7

DISCONNECTING THE WINDROWER

In order to disconnect the windrower from the tractor perform the following:

•

lower windrower support and secure with linchpin,

•

lower windrower using three-point linkage to rest position,

•

switch of tractor engine and remove key from ignition,

•

disconnect articulated telescopic shaft,

•

disconnect top link of three-point linkage,

«
...
43
44
45
46
47
...
»

Содержание ZKP350





























































Отзывы:

Нет отзывов