ProMinent DULCOTROL DWCa Скачать руководство пользователя страница 79

Страница: 79 / 140

CAL pH

Asymmetry

Buffer 2:

A1019

Zero point

Slope

% Slope

Accept with <CAL>

Buffer 1:

Calibr.param. for 25 °C

Fig. 40: Display of the calibration result
16.

Incorrect calibration
An error message appears if the result of the

calibration lies outside the specified tolerance

limits. In this case the current calibration is

not carried over.
Check the prerequisites for calibration and

eliminate the error. Then repeat calibration.

Cleaning and care of pH and ORP sensors
Please note the separate instructions sup‐

plied with the pH and ORP sensors for

cleaning and care of pH and ORP sensors.
After cleaning, the sensor must be condi‐

tioned in 3-molar potassium chloride solution

for 60 minutes before it can be reused for

calibration.

Carry over the result of the calibration into the controller

memory by pressing .

The controller shows the continuous display again and

operates with the results of the calibration.

15.1.1.3

pH sensor calibration (CAL) with an external sample (1-point)

Measuring and control behaviour of the controller

during calibration
During calibration the actuating outputs are deacti‐

vated. Exception: a basic load or a manual control

variable has been set. This remains active. The

measured value output [standard signal output mA]

is frozen, corresponding to its settings in the mA

output menu.
When calibration/testing has been completed suc‐

cessfully, all of the error checks relating to the

measured value are restarted. The controller saves

all the determined data for zero point and slope

upon a successful calibration.

Calibrating the controller diaLog DACb

Содержание DULCOTROL DWCa













































































































































Результаты поиска

Содержание DULCOTROL DWCa

Отзывы:

ProMinent DULCOTROL DWCa, Руководство по сборке и эксплуатации, Страница: 79 / 140

Результаты поиска

Содержание DULCOTROL DWCa

Отзывы: