ProMinent DULCOTROL DWCa Скачать руководство пользователя страница 101

Страница: 101 / 140

CAL O2

A2851

Zero point

Slope

Last calibration

22.09.2019 14:22:33

4.00 mA

100% (0.80 mA/ppm)

Calibration of zero point

Slope calibration by

reference measurement in water

Calibration of the slope in air

Fig. 64: Calibration of the slope in air
3.

Use OK to select the calibration process: Calibration of the

slope in air.

The display appears as follows:

CAL O2

A2852

Air pressure

Process temperature

Temperature

Manual

1013 mbar

10 °C

Salinity

Conductivity

Higher than NNl

2) continue with <CAL>

1) Enter correcting value

300 m

0.0 mS/cm

0 g/l

Fig. 65: Correction variable values
4.

Enter the current values for the correction variables: Use OK

to select the correction variable. Use the arrow keys to enter

the values.

Use CAL to continue.

The display appears as follows:

CAL O2

A2853

Sensor current

Concentration

Latest sensor measured values

12.61 mA

11.10 ppm

2) Wait for the stability of the measured value

1) Immerse sensor in

buffer

Fig. 66: Keeping the sensor in air saturated with water vapour
6.

Keep the sensor in air saturated with water vapour.

Calibrating the controller diaLog DACb

101

Содержание DULCOTROL DWCa













































































































































Результаты поиска

Содержание DULCOTROL DWCa

Отзывы:

ProMinent DULCOTROL DWCa, Руководство по сборке и эксплуатации, Страница: 101 / 140

Результаты поиска

Содержание DULCOTROL DWCa

Отзывы: