ProMinent DULCOTROL DWCa Скачать руководство пользователя страница 66

Страница: 66 / 140

Commissioning the Compact Controller for Inductive Con‐

ductivity

User qualification: trained user, see

WARNING!
Sensor run in period
This can result in dangerous incorrect metering
Consider the run in period of the sensor during

commissioning:
– Correct measuring and metering is only pos‐

sible if the sensor is working perfectly.

– It is imperative that you adhere to the run in

periods of the sensor.

– Calculate the run in period when planning com‐

missioning.

– It may take a whole working day to run-in the

sensor.

– Observe the sensor operating instructions.

13.1 Measured variables

The controller can process the following measured variables:

Inductive conductivity

[ConI]

Resistance

[RES]

TDS value

[TDS]

Salinity

[SAL]

Use the key to switch between the controller's measured varia‐

bles

[ConI], [RES], [TDS] and [SAL] in the continuous display.

Depending on the measured variable set, the settings of variables

are changed or the variables are hidden completely in the

[INPUT

TCOMP] menu and in the [LIMIT] menu.

Symbol displayed in the controller's display:

[ConI]

Units of measurement: μS/cm, mS/cm , S/cm. The measuring

range is automatically detected and switched by the controller
Physical variable: specific electrical conductivity (K). Only this

measured variable and the correction variable

‘Temperature’ are

emitted at the mA output, independently of the measured variable

set on the controller. The setting of the measured variable on the

controller only affects the layout of the display and not the output at

the mA output.

Symbol displayed in the controller's display:

[RES]

Units of measurement: MΩcm, kΩcm, Ωcm. The measuring range

is automatically detected and switched by the controller
Physical variable: specific electrical resistance.
Calculating the specific resistance: ρ (T

ref

) = 1/K (T

ref

)

Switching between measured varia‐

bles

Measured variable: Inductive conduc‐

tivity

[ConI]

Measured variable: Resistance

[RES]

Commissioning the Compact Controller for Inductive Conductivity

Содержание DULCOTROL DWCa













































































































































Результаты поиска

Содержание DULCOTROL DWCa

Отзывы:

ProMinent DULCOTROL DWCa, Руководство по сборке и эксплуатации, Страница: 66 / 140

Результаты поиска

Содержание DULCOTROL DWCa

Отзывы: