ProMinent DULCOTROL DWCa Скачать руководство пользователя страница 48

Страница: 48 / 140

Starting-up Sensors

User qualification: trained user, see

WARNING!
Sensor run-in periods
This can result in hazardous incorrect metering.
– Correct measuring and metering is only pos‐

sible if the sensor is working perfectly

– Observe the sensor operating instructions

– Calibrate the sensor after commissioning

WARNING!
Danger from hazardous substances!
Possible consequence: Fatal or very serious inju‐

ries.
Please ensure when handling hazardous sub‐

stances that you have read the latest safety data

sheets provided by the manufacture of the haz‐

ardous substance. The actions required are

described in the safety data sheet. Check the

safety data sheet regularly and replace, if neces‐

sary, as the hazard potential of a substance can be

re-evaluated at any time based on new findings.
The system operator is responsible for ensuring

that these safety data sheets are available and that

they are kept up to date, as well as for producing

an associated hazard assessment for the worksta‐

tions affected.

CAUTION!
– The sampling tap must be closed, otherwise

sample water can escape.

– The sample water should be free from air bub‐

bles to ensure reliable measurement and con‐

trol. Should the sample water carry air with it

as a result of the process, then suitable means

must be used to separate out the air.

– Please also observe the operating instructions

for controllers and fittings and any other units,

such as sensors, sample water pumps ...

Maximum permissible operating pressure: 1 bar at maximum 45 °C

or see

10.1 Preparation of Sensors

Tighten all threaded connectors and check that the threaded

connectors are leak-tight.

Check the positions of all shut-off valves. The position of the

shut-off valves has to guarantee that the

DULCOTROL

measuring/control station is tight and that

there is a flow of sample water.

Starting-up Sensors

Содержание DULCOTROL DWCa













































































































































Результаты поиска

Содержание DULCOTROL DWCa

Отзывы:

ProMinent DULCOTROL DWCa, Руководство по сборке и эксплуатации, Страница: 48 / 140

Результаты поиска

Содержание DULCOTROL DWCa

Отзывы: