ProMinent DULCOTROL DWCa Скачать руководство пользователя страница 109

Страница: 109 / 140

Once you have selected the sensor type, the prompt automatically

appears asking whether the sensor parameters (zero point) have

to be determined. You can initiate this prompt manually as follows:
Continuous display ➨ Menu ➨ or

[Measurement] ➨ ➨

[Measuring channel X Conductivity] ➨ or

[Sensor parameter adjustment] ➨ .
1.

Use the arrow keys to select

[Automatically determine sensor parameters].

Continue with .

You will see the display showing

[Sensor dry] and

[Automatically determine sensor parameters].

Continue with .

You will see the display with the message

[Sensor parameters are automatically determined].
The sensor parameters are automatically carried over.

15.1.8.2

Calibrating conductive conductivity, cell constant

Prerequisite for calibration. The conductivity sensor is connected.

The conductivity sensor is in a conductivity calibration solution, the

conductivity of which is known.

Material

Order number

Conductivity calibration solution, 1413 μS/cm, 250 ml.

1027655

Conductivity calibration solution, 1413 μS/cm, 1000 ml.

1027656

Conductivity calibration solution, 12.88 mS/cm, 250 ml.

1027657

Conductivity calibration solution, 12.88 mS/cm, 1000 ml.

1027658

All parameters for the conductivity sensor are correctly entered in

the

[Measurement] menu item.

Press in the continuous display.

Use the arrow keys to select the channel which should be

calibrated.

Then press

You will see the display with the menu for selection of

[Cell constant] or [Temp. coefficient].

Use the arrow keys to select

[Cell constant].

Continue with .

You will see the current data for the

[Cell constant]. Enter

the temperature coefficient of the calibration solution

here.

Continue with calibration with .

Continue with .

Enter the known conductance of your conductivity calibration

solution.

Accept with .

10. Continue with .

Calibration of the cell constant

Calibrating the controller diaLog DACb

109

Содержание DULCOTROL DWCa













































































































































Результаты поиска

Содержание DULCOTROL DWCa

Отзывы:

ProMinent DULCOTROL DWCa, Руководство по сборке и эксплуатации, Страница: 109 / 140

Результаты поиска

Содержание DULCOTROL DWCa

Отзывы: