ProMinent DULCOTROL DWCa Скачать руководство пользователя страница 30

Страница: 30 / 140

7.1 Fitting the DGMa with Sensors

Remove the upper blanking plug from a module

With pH/ORP sensors: remove the sensor from its transport

protection container.

Screw in the sensor.
With the DULCOTEST

Perox sensor, screw the flow resister

of an in-line probe housing module into the module from

below

Sensitive sensors are not ready mounted but sup‐

plied loose with the measuring plate in their orig‐

inal packaging.
Push the sensor slowly into the in-line probe

housing, as the sensor diaphragm can otherwise

extend

Requirement
The sensor is filled with electrolyte and the dia‐

phragm cap is screwed on tightly.
Accessories: Mounting kit, part number 815079.
Refer to the operating instructions for the respec‐

tive sensor.

Remove the upper blanking plug from a 25-mm module

Push the O-ring (4) first, then the assembly washer (5) onto

the sensor (3) from below

Push the holding bolt (1) from above onto the sensor (3)

Carefully push the sensor (3) into the module

Tighten the holding bolt (1)

Carefully push the flow resister (6) down into the module

Fitting sensor with PG 13.5 connector:

Amperometric sensors with

Ø = 25 mm

A1247

Fig. 6: Fitting the sensors

Installing Sensors in the Bypass Fitting DGMa

Содержание DULCOTROL DWCa













































































































































Результаты поиска

Содержание DULCOTROL DWCa

Отзывы:

ProMinent DULCOTROL DWCa, Руководство по сборке и эксплуатации, Страница: 30 / 140

Результаты поиска

Содержание DULCOTROL DWCa

Отзывы: