progeo TEKNA ADVANCE Series Скачать руководство пользователя страница 19

Страница: 19 / 45

REHATEAM s.r.l.—vicolo Negrelli 5—31040 Castagnole di Paese TV

www.rehateamprogeo.com

Service Manual TEKNA ADVANCE 19

SERVICE MANUAL

SIDE GUARD

Standard rear frame

When you change the setting

, you have to move the side guard

frontward or backward according to the new position of the rear
wheel, but the height of the side guard remains the same.

1. After the setting adjustment, remove the bolt

2. Loosen the two bolts and nuts

E1 E2

fixing the plate of support

to the frame.

3. Put the wheel on and slide the plate

forward or backward.

Position the side guard at 5 mm from the tyre. If necessary, you
can loosen the bolt and nut

C1 C2

and slide the side guard or

you can also fix the plate

over the seat tube support

with

the bolt and nut

G1 G2

4. Fix the two bolts and nuts

E1 E2

(o E1 E2 + G1 G2).

5. You have now to drill a new hole for the bolt

. With a pointed

tool through the hole of the ring

, make a mark on the side

guard.

6. Drill a 6 mm hole
7. Insert the bolt and washer

and fix the side guard. Make sure

to fix bolt and nut

C1 C2

, too.

8. Check and if necessary adjust the brake.

When you change both the rear height and the setting

, you have to move the side guard up or down

and

forward or backward.

1. After the rear wheel height and position adjustment, remove the bolt

and the bolt and nut

C1 C2

. This way you remove the side

guard.

2. Put the wheel on.

3. Adjust the brake by moving the plate of support

along the frame (see points 2 and 3 of the adjustment

4. Position and hold with one hand the side guard at approximately 5 mm from the tyre and parallel to it if (you can lean the side guard on

the outside of the plate of support as in adjustment

5. You have now to drill a new hole for the bolt

, thus, while holding the side guard in position, make a mark on the side guard with a

pointed tool through the hole of the ring

6. Drill a 6 mm hole.

7. Insert the bolt and washer

and fix the side guard.

8. Follow points 4 to 8 of adjustment

according to the adjustment.

9. If the slots of the plate

do not allow fixing the side guard, you may move it accordingly.

10.Finally check and, if necessary, adjust the brake.

Mark where

to drill the

new hole

Содержание TEKNA ADVANCE Series














































Результаты поиска

Содержание TEKNA ADVANCE Series

Отзывы:

Похожие инструкции для TEKNA ADVANCE Series

Бренды по названию

Популярные бренды

progeo TEKNA ADVANCE Series, Руководство по обслуживанию

Результаты поиска

Содержание TEKNA ADVANCE Series

Отзывы:

Похожие инструкции для TEKNA ADVANCE Series

Бренды по названию

Популярные бренды