background image

625-505revI-EN

3

Printed in U.S.A. 1/06 © 2006

Steamer

625-MCD & MFY

Temperature Calibration

A. Press and hold the TEMPERATURE button. The display will 

show the current temperature setting for Celsius (C) or 
Fahrenheit (F).

B. While holding the TEMPERATURE button, press the C/F 

button to change the setting between Fahrenheit and Celsius.

C. Release the TEMPERATURE button to store the new value.

1

A. Press the UP or DOWN Arrow button until the temperature 

readout matches the calibration reading.

B. Press the RAPID STEAMER LOGO button to store the desired 

calibration and exit CAL TEMP Mode.

NOTE: Pressing the PRODUCT 3 button at any time exits the 
Program Mode without storing the change.

3

View Firmware Version

Press and hold the RAPID STEAMER LOGO button first, then press 
and hold the START button. The display will show the current firmware 
version.

. VERS  XX.XX

The CAL TEMP Mode is used to calibrate the platen temperature 
with an external meter connected to the meter plug inlet on the 
bottom right side of the unit. Add ± 5°C (± 10°F).

2

A. Press and hold RAPID STEAMER LOGO button and immediately 

press and hold the TEMPERATURE button. Hold for 6 seconds.

B. The display now shows the current calibration temperature.

C. Press the PRODUCT 2 button to zero any previous calibration offset 

value. The display will now show the platen temperature without any 
calibration offset.

Factory Presets

Loading factory presets restores the unit to factory settings and voids 
all user programmed information.

A. During power up, press and hold both PRODUCT 1 and 

PRODUCT 4 buttons within 3 seconds. The display will flash 
PRESETS LOADED.

B. Release both buttons.

625-MCD
Default Factory Presets:

ON OFF Cycles Delay

1.5

3.0

2

2.5

625-MFY

Default Factory Presets:

ON OFF Cycles Delay

0.5

1

6

2.5

Manual Reset

A hi-limit thermostat will turn off electrical power to the platen and 
control circuits if the unit overheats.

Turn the unit off and allow to cool (approximately 10 – 15 minutes).

A manual reset is located on the back of the unit. Once the unit has 
cooled sufficiently, remove the cap and press the manual reset and 
restart the unit. Replace the manual reset cap.

NOTE: If the unit continues to shut off due to overheating, contact your 
authorized Prince Castle Service Agency.

Manual 

Reset

Содержание 625-MCD


















Отзывы: