Primus Wind Power Air 30 Скачать руководство пользователя

Страница: 7 / 54

AIR 40, AIR Breeze, AIR 30, AIR X MARINE and AIR SILENT-X are trademarks of Primus Wind Power 2013 Primus Wind Power Inc.

AIR Owner’s Manual

3-CMLT-2020-A

PRIOR TO INSTALLATION

Siting Tips for Permanent Installations

PROPER SITING: Better Performance & In creased Longevity Look at vegeta-

tion deformation to determine best area and prevailing wind direction

Griggs-Putnam Index.

*Probable mean annual windspeed. Data prepared by

E.W. Hewson, J.E. Wade, and R.W. Baker of Oregon State University

EXCESSIVE TURBULENCE = Fatigue Damage & Shorter Turbine Life

Prevailing wind

Excess

76 m (250 ft)

Turbine should be a minimum of 76m (250 ft) away from and 6m (20 ft)
above obstacles

ATYPICAL SITING CONSIDERATIONS

Coastal or Lakeside

Trees and taller structures can be
down-wind.

Ridge Tops

Wind compresses as it blows
over the top of a hill, increasing
the wind speed.

Plateau/Mesa/Structures

Site the generator far enough from
the cliff to avoid turbulent wind.
The vertical face of any structure
will cause turbulence and affect
overall performance.

Содержание Air 30























































Результаты поиска

Содержание Air 30

Отзывы:

Похожие инструкции для Air 30

Бренды по названию

Популярные бренды

Primus Wind Power Air 30, Руководство пользователя

Результаты поиска

Содержание Air 30

Отзывы:

Похожие инструкции для Air 30

Бренды по названию

Популярные бренды