Primus Wind Power Air 30 Скачать руководство пользователя | Manualshive

Страница: 12 / 54

background image

AIR 40, AIR Breeze, AIR 30, AIR X MARINE and AIR SILENT-X are trademarks of Primus Wind Power 2013 Primus Wind Power Inc.

AIR Owner’s Manual

3-CMLT-2020-A

12

Blade to Hub Assembly

(STEP 1)

3/16”

Assembled blade

WARNING:

Nylock nuts and greased blade bolts may only be used

one time; replace after each use.

NOTE: See Appendix B: AIR Silent X Blade Set and Further Installation Recommendations

Assembly blade set first using proper torque for hardware and
application of tef-gel included.

AIR 30 and AIR X Marine units, it is recommended to perform tip to tip
measurment of blades prior to properly securing hub to avoid vibration.
The hub blade root allows for adjustment of the blade position.  There-
fore, it is recommended to adjust the distance between each blade tip.
The blades should have a distance from blade tip to blade tip approxi-
mately equal between all three blades.

and AIR X Marine

IMPORTANT:

Tef-Gel is a corrosion inhibitor and is especially

important in marine applications. Tef-Gel should be applied
to all blade bolts and yaw bolts using the applicator and Tef-
Gel provided with your hardware kit. Tef-Gel helps to pre-
vent corrosion and lubricates threads (recommended for both
land and marine usage).

«
...
10
11
12
13
14
...
»

Содержание Air 30























































Отзывы:

Нет отзывов

Похожие инструкции для Air 30

Бренд: Valen Страницы: 14

3kW Grid-Tie HAWT

Бренд: TECO ECO Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды