Primus Wind Power Air 30 Скачать руководство пользователя | Manualshive

Страница: 50 / 54

background image

AIR 40, AIR Breeze, AIR 30, AIR X MARINE and AIR SILENT-X are trademarks of Primus Wind Power 2013 Primus Wind Power Inc.

AIR Owner’s Manual 3-CMLT-2020-A

50

APPENDIX B

(continued)

SILENT X BLADE KIT COMPONENTS

ROTOR BLADES

Check  if the blades  show damages  ( e . g .   broken  edges,  damaged
surface or cracks).  you notice any  damage, the  generator must
not  be  used  any  longer.  Check

blade bolt tightness one day

after mounting and after that every 3-6 months. Eventually then

can go to a longer

ADVANCED HUB DESING AND HARDWARE / NOSE CONE

A new advanced hub design allows for the blades to be slipped into the hub with very little
movement. This new hub eliminates the need to any tip to tip measurements of the blade.
Included with each blade set is a washer for behind hub and rotor shaft. This washer is an
optional install  and only should be used if there is rubbing from hub to AIR turbine Face that
impedes free movement of rotor hub. Most AIR installs will not require this washer.  NOTE:
In addition to the washer you will find Tef-Gel and applicator in your hardware kits. Tef-Gel
should be applied to all bolts prior to installation to prevent corrosion and lubricate threads
for proper fit. Applicable to both land and marine AIR units.

Fig. 1 Blade Set (set of (3))

Fig. 2 Hub and Hardware

Fig. 3 Nose Cone (white)

NOTE:  The Silent X Blade Kit (Upgrade Kit) can be retrofitted to all Primus
Wind Power wind turbine models.  For further information contact Primus
Wind Power directly.

«
...
48
49
50
51
52
...
»

Содержание Air 30























































Отзывы:

Нет отзывов

Похожие инструкции для Air 30

Бренд: Rutland Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды