PowerBoss Armadillo 9X Скачать руководство пользователя

Страница: 80 / 96

Armadillo 9X Sweeper #4100033 Rev. D 07/15

Page 80

Adjusting The Parking Brake Cable Length

1. Park the machine on a level surface and chock

the wheels.

2. Place the parking brake lever in the “OFF”

position.

3. Turn the knurled handle counter-clockwise as far

as possible.

WARNING

Do not rely upon the hydraulic cylinders to keep

the hopper raised for maintenance. Always

engage the safety arm before servicing in the

area of the hopper.

4. Raise the hopper and engage the safety arm.
5. Locate the cable clevis ends for the parking

brake cables.

6.  Disconnect the clevis ends from the bar.
7.  Loosen the jam nuts at the base of the clevis.
8.  Turn the clevis clockwise three or four complete

turns.

9. Tighten the jam nuts and re-install the clevis

ends onto the bar.

10. Adjust the knurled handle on the parking brake

lever.

BRAKE CABLE

CLEVIS END

JAM NUTS

PREVENTATIVE MAINTENANCE

Содержание Armadillo 9X

































































































Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды

PowerBoss Armadillo 9X, Руководство пользователя

Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды