PowerBoss Armadillo 9X Скачать руководство пользователя

Страница: 68 / 96

Armadillo 9X Sweeper #4100033 Rev. D 07/15

Page 68

8. Once the broom is started onto the drive hubs,

rotate the broom counter-clockwise while

pushing lightly against the broom.

9. Once the broom is fully engaged, replace the

idler hub while aligning the seats in the idler hub

with the broom’s drive hub ears.

10. Install the retaining bolt into position and

tighten with the wrench.

11. Close and latch the left broom door.
12. Perform a main broom adjustment test and

adjust as needed.

Side Broom Angle Adjustment

The angle adjustment is controlled with a stop bolt.

This stop bolt is located at the top front of the side

broom arm (under the spring). To increase the angle of

the side broom, loosen the jam nut and turn the stop

bolt counter-clockwise. Be sure to retighten the jam nut

back down once the adjustment is made.

Side Broom Height (Wear) Adjustment

The height of the side broom is adjusted with the

use of a stop bolt located at the lower rear of the

curb broom arm. As the side broom wears, it will be

necessary to lower the arm.

Adjust Side Broom Height

To lower the side broom, loosen the jam nut on the

stop bolt. Turn the stop bolt in a counter-clockwise

direction, check the side broom for proper contact and

re-tighten the jam nut.

PREVENTATIVE MAINTENANCE

Содержание Armadillo 9X

































































































Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды

PowerBoss Armadillo 9X, Руководство пользователя

Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды