PowerBoss Armadillo 9X Скачать руководство пользователя

Страница: 78 / 96

Armadillo 9X Sweeper #4100033 Rev. D 07/15

Page 78

WARNING

Do not rely upon the hydraulic cylinders to keep

the hopper raised for maintenance. Always

engage the safety arm before servicing the

hopper.

Loosen the mounting bolts in the gasket mount.

Move the assembly toward the hopper. Tighten the

bolts. Test and repeat if necessary.

Flap Replacement

Flaps located at the entrance lip and on the sides of

the hopper must be replaced when worn or damaged.

The flap panels may be replaced separately.

1. Park the machine on a level surface and engage

the parking brake.

2. Raise the hopper.

PREVENTATIVE MAINTENANCE

SAFETY

ARM

ENGAGED

Vacuum Gasket Mount Adjustment

•

With the hopper in the normal position, observe

contact between the back of the hopper and

gasket. If complete seal is not maintained, raise

the high dump hopper.

Содержание Armadillo 9X

































































































Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды

PowerBoss Armadillo 9X, Руководство пользователя

Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды