PowerBoss Armadillo 9X Скачать руководство пользователя

Страница: 60 / 96

Armadillo 9X Sweeper #4100033 Rev. D 07/15

Page 60

Latches & Hinges

The hinges and latches and all doors and covers

should be lubricated with oil every 500 hours. There

are numerous hinges and latches, make sure to

lubricate all of the following:

•

Engine cover

•

Side Door

•

Main Broom Door

•

Seat Hinge

•

Engine latch

Hopper Lift Arm Mounts

The hopper lift arm mounts must be lubricated

every 500 hours with lithium grease, There are two

lubrication point on each mount.

1. Park the machine on a level surface.

WARNING

Do not rely upon the hydraulic cylinders to keep

the hopper raised. Always engage the safety arm

before servicing the hopper.

2. Raise the hopper and engage the safety arm
3. Shut off the engine and engage the parking

brake.

4. Locate and grease the hopper lift arm lubrication

points.

SAFETY

ARM

ENGAGED

PREVENTATIVE MAINTENANCE

Содержание Armadillo 9X

































































































Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды

PowerBoss Armadillo 9X, Руководство пользователя

Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды