PowerBoss Armadillo 9X Скачать руководство пользователя

Страница: 38 / 96

Armadillo 9X Sweeper #4100033 Rev. D 07/15

Page 38

TRANSPORTING THE MACHINE
Using a Trailer or Transport Vehicle

1. Position the machine on the transport vehicle

or trailer and apply the parking brake.

2. Tie the machine down using the tie down holes

in the frame forward of the front wheels and the

hook bracket in the rear center of the frame.

NOTE: Attach the tie downs to the frame only.
Pushing the Machine

Push the machine from the front or rear using the

bumpers only.

ATTENTION!

Do not tow or push the machine a distance of

more than 0.5 mi (0,8 km) or faster than 1 mph

(1,6 km/hr). Exceeding these restrictions may

cause damage to the hydraulic system. If towing

will exceed the above restrictions, the rear

wheel must be raised or supported by a dolly.

MACHINE OPERATION

Содержание Armadillo 9X

































































































Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды

PowerBoss Armadillo 9X, Руководство пользователя

Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды