PowerBoss Armadillo 9X Скачать руководство пользователя

Страница: 66 / 96

Armadillo 9X Sweeper #4100033 Rev. D 07/15

Page 66

Main Broom Height Adjustment

1. Turn the machine off and lock the parking brake.
2. Position the main broom lever in the LOWER

position.

NOTE: The adjustment knob is located in the

engine compartment on the broom control

handle pivot.

3. Turn the broom adjusting knob clockwise one-

eighth turn to free the wing nut.

4. Turn the wing nut counter-clockwise to allow

space for adjustment.

5. Make a lower or higher adjustment with the knob

as required.

6. Retighten the wing nut.
7. Repeat the main broom adjustment test to see

that the broom is properly adjusted.

Main Broom Taper Adjustment
NOTE: It is not usually necessary to perform this

adjustment. However, if the main broom

adjustment test shows a pattern that is

tapered in length (one end is wider than

the other), perform the procedures which

follow.

1. Locate the adjusting screws directly beneath the

hydraulic pump.

2. Loosen the jam nuts on the adjusting screws,

and loosen the retaining bolt on the inside of the

mounting bracket.

Use the adjusting screws to raise or lower the

left end of the main broom. (The right end of the

broom remains fixed. All adjustments affect the

left end of the broom.)

4. After adjustment, tighten the retainer bolt and

adjusting screws.

5. Repeat the main broom adjustment test to see

that the broom is properly adjusted.

PREVENTATIVE MAINTENANCE

Содержание Armadillo 9X

































































































Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды

PowerBoss Armadillo 9X, Руководство пользователя

Результаты поиска

Содержание Armadillo 9X

Отзывы:

Похожие инструкции для Armadillo 9X

Бренды по названию

Популярные бренды