4 0 0 0 T
61
5.12 Battery Routine Checks
Keep battery clean by periodically wiping it
with a damp cloth. Keep the water level in
the battery topped up. Remove the caps and
if the water level is low add distilled water so
that the lead plates in the battery are
covered.
Keep all connections clean and tight. Remove
any corrosion, and wash terminals with a
solution of 1 part baking soda and 4 parts
water. Tighten all connections securely.
Keep battery fully charged, especially in cold
weather. If a battery charger is used, turn
charger off before connecting charger to
battery. Attach positive battery charger lead
to positive battery post. Then attach negative
battery charger lead to a good ground.
5.13 Main Control Panel Warning
Lights
Lights that are controlled by the engine
controller board are illuminated for 2 seconds
upon switch on as a standard lamp test. This
excludes: Battery charge warning light, engine
run light and engine pre-heat indicator light.
1. Battery Charge Warning Light
Lights upon start up only - if it fails to light
there is a fault in the charging circuit. Stop
engine and check circuit.
2. Oil Pressure Warning Light
Lights upon start up only – if a fault occurs in
the oil pressure system the light will
illuminate and the engine will shut down after
2 seconds.
3. Temperature Warning
Lights if there is overheating in the cooling
system. Engine shuts down 5 seconds after
the fault has been detected.
4. Proximity Sensor Warning Light
See Section 1.9
5. Engine Run Light
Light must stay on for engine to run. If it goes
out then a machine stop has been pressed
and the engine will shut down immediately.
6. Air Breather Restriction
Only lights air breather system receives a fault
signal for 30mins continually - Engine shuts
down & the light stays on until ignition key
has been turned off & fault rectified.
7. Fuel On Light
Light must remain on during crank and engine
run.
8. Hydraulic Oil Level Warning
Lights if the hydraulic oil level is low and
causes engine shutdown 5 seconds after
detection.
1
. 2
. 3
. 4
. 5
. 6
. 7
. 8
.
9
.
10
. 11
.
Содержание 4000T
