manualshive.com logo in svg

Polytec TMS-500 TopMap Pro.Surf, Руководство по эксплуатации

Поделиться
Скачать
Polytec TMS-500 TopMap Pro.Surf Скачать руководство пользователя страница 30

3-16

3 First Steps

3.4

Cabling 

 

 

WARNING!
Electric shock caused by connection to wrong power supply!

» Connect up the instruments only using a three-pin mains cable to AC 

systems 50/60 Hz with a grounded protective conductor, and a nominal 

voltage of between 100 V and 240 V.

 

 

ATTENTION!
Damage to the instrument caused by overvoltage!

» First of all, connect up all components as described in this chapter before 

connecting the mains cable and switching on the instrument.

 

 

ATTENTION!
Damage to connections caused by bent contact pins!

All cables must be easy to plug in.
» Check the contact pins before plugging in the cables.
» Do not use any force when plugging in the cables.
» Replace defective cables with new cables.
» If necessary, contact your local Polytec representative.

In the following you will find a description of all necessary steps to connect up 

the instrument. All the cabling is also shown in F

IGURE

3.12. Secure the 

connections accordingly.

If you have any problems connecting up the cables, contact your local Polytec 

representative.

3.4.1

Connecting the Hardware 

Peripheral 

devices 

1. Connect up the mouse, the keyboard, and the joystick to the back of the 

industrial PC.

2. Plug the monitor cable into the DisplayPort jack on the monitor and into 

the 

DP3

 Mini DisplayPort jack on the back of the industrial PC. 

Industrial PC to 

controller 

3. Plug the yellow network cable (motor controller connection) into the 

MOTOR

 network connection on the back of the industrial PC and into the 

ETHERNET

 network connection on the back of the controller.

 

 

ATTENTION! 
Impaired functionality caused by incorrect cabling!

» Solely use the USB 3.0 cable enabled by Polytec to connect the industrial 

PC and the sensor head.

Industrial PC to 

sensor head 

4. Plug the USB 3.0 cable into the 

VIDEO

 USB connection on the back of the 

industrial PC and into the 

VIDEO

 USB connection on the bottom of the 

sensor head.

Содержание TMS-500 TopMap Pro.Surf






























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды