Polytec TMS-500 TopMap Pro.Surf Скачать руководство пользователя страница 10

Страница: 10 / 61

1-6

1 Safety Information

1.4

Lamp Safety

1.4.1

Important Warning Notices

WARNING!
Damage to eyes caused by high light intensity!

» Do not look directly into the illumination module.
» Do not use any operating or calibrating equipment other than specified

here.

1.4.2

Applicable Standards and Directives

Polytec instruments comply with the standards IEC and EN 62471

(Photobiological Safety of Lamps and Lamp Systems).

1.4.3

Equipment

Illumination

module

The instrument is equipped with an L

-based illumination module.

Safety

equipment

The L

is switched on or off together with the controller.

Beam exit

aperture

The position of the beam exit aperture is shown in the following figure.

Figure 1.4:

Position of the beam exit aperture with the beam direction [1]

1.4.4

Information on Risk Category 0

The instrument complies with risk category 0 and does not pose any

photobiological danger. This includes looking directly into the beam during

normal operation over a long period of time.

Under any operating conditions, there is no risk to skin.

Содержание TMS-500 TopMap Pro.Surf






























































Результаты поиска

Содержание TMS-500 TopMap Pro.Surf

Отзывы:

Бренды по названию

Популярные бренды

Polytec TMS-500 TopMap Pro.Surf, Руководство по эксплуатации

Результаты поиска

Содержание TMS-500 TopMap Pro.Surf

Отзывы:

Бренды по названию

Популярные бренды