background image

 

ID-E299-001GB 

35 

ML3-1240 

17 – 18 

+  -  – 

LK3 monitoring line 

ML3-1240 

37 – 38 

+  -  – 

LA3alarm line 

ML3-1240 

19 – 39 – 40 

NO – C – NC 

P27 general fault relay 

MZ-4212 

Z5; Z6 

+  -  – 

24 V ext. devices power supply (max. 0.8A) 

12  

MAINTENANCE 

12.1  

GENERAL RULES 

Fire alarm systems, as safety installations, must be continuously kept at full efficiency, therefore they 
require  proper  maintenance.  The  premises  user  is  obliged  to  ensure  the  installation  maintenance, 
best of all by signing an agreement with a maintenance technician.  

The maintenance consists in carrying out periodical inspections and removal of possible faults. The 
maintenance technician should thoroughly study this manual. He should know exactly the operating 
principles of the control panel and interoperating manual and automatic fire warning devices, as well 
as  other  devices  connected  to  the  control  panel.  It  is  highly  recommended  to  pass  a  training 
organized by the manufacturer that covers fire alarm systems application, installation and operation. 
The  maintenance  technician  should  also  know  the  premises  territory,  displacement  of  the  system, 
detector  line  routes,  arrangement  of  fire  detectors  and  manual  call  points,  and  environmental 
conditions that may influence the devices work. 

12.2 

PERIODICAL TESTING 

The periodical checks consist in operation tests of every line element installed in the detection lines, 
the control panel and its output circuits: the lines that control external acoustic signalling devices or 
fire-fighting  devices,  as  well  as  the  protecting  device  monitoring  line  and  the  monitoring  system 
circuits.  

The periodical tests should be executed in accordance PKN-CEN/TS 54-14: 2006 standard. 

Periodical testing frequency:  the manufacturer recommends executing the periodical tests at least 
once  per  year.  Nevertheless,  the  system  owner,  in  agreement  with  the  system  designer  and  the 
maintenance technician, should increase the test frequency, if the system operating conditions are 
hard (high humidity, corrosion environment, dusting, etc.). 

The periodical testing consists in: 

-

 

event  memory  readout  (using  a  computer),  in  order  to  check  the  control  panel  attending 

personnel appropriate work and possible signals indicated by the control panel; 

-

 

inspection  (testing)  of  every  signalling  diode  and  acoustic  signalling  device  of  the  control 

panel; 

-

 

consecutive  testing  of  every  fire  detector  (e.g.  using  imitators)  and  manual  call  points 

installed in every detector line, utilising a possibility to switch any line for testing; 

-

 

visual evaluation of the fire detectors technical condition (level of dirt, corrosion, permanent 

soil)  and  of  manual  call  points,  especially  in  case  of  their  longer  operation,  that  should  be 
carried out during a device testing; 

-

 

if necessary, cleaning of the fire detectors and  their replacement or regeneration; 

-

 

checking  the  external  signalling  devices  and  connected  protective  and  fire-fighting  devices 

under condition that the premises user is informed and taking necessary measures to avoid 

Содержание Ignis 1000














































Отзывы: