background image

 

6

 

HARNESS DESCRIPTION 

 

5 PIN MAIN IGNITION HARNESS 

 

WIRE 

Wire color 

Function 

Description 

RED 

+12 VOLT 

BATTERY 

 

Connect to the largest 12-volt supply wire at the IGNITION 
harness.  Ensure that the OEM power wire is fused greater than 25 
amps. 

YELLOW  

30 AMP 

IGNITION 

OUTPUT  

Connect to vehicle’s IGNITION wire.  Source wire should have 
+12 volts with the key in the RUN and CRANK position. 

VIOLET  

30 AMP 

STARTER 

OUTPUT  

Connect to the vehicle’s starter wire.  Source wire should have +12 
volts with the key in the CRANK position only. 

ORANGE  

30 AMP 

ACCESSORIES 

OUTPUT 

 

Connect to the vehicle’s Accessories wire.  The source wire must 
have power in the Accessories position only. (NO power in the 
CRANK position) 

RED 

+12 VOLT 

BATTERY 

Connect to the largest 12-volt supply wire at the IGNITION 
harness.  Ensure that the OEM power wire is fused greater than 25 
amps. 

 

 
 
7 PIN SECONDARY HARNESS 

 

WIRE 

Wire color 

Function 

Description 

BLACK 

(-) CHASSIS 
GROUND INPUT 

This wire must be connected to bare, unpainted metal.  It is 
preferable that you use a factory ground bolt rather than a self-
tapping screw.  

Screws tend to get loose or rusted over time and 

can cause erratic problems.

 

VIOLET 

A/C 
TACHOMETER 
INPUT WIRE 

This wire must be connected to the negative side of the IGNITION 
coil in vehicles that use conventional coil systems.  In multi-coil 
systems the TACH wire may be difficult to locate.  

NOTE:

 A 

TACH learning must be done after the installation is completed. 

GREY 

(-) HOOD 
SWITCH WIRE 

Connect this wire to the installed underhood PIN-SWITCH (HOOD 
SWITCH) supplied.  This input will disable or shutdown the remote 
starter when the HOOD is opened. 

WHITE 

GROUND 
OUTPUT 

500 mA. constant ground output when running. 
Will become active before remote IGNITION ON, and stays active 
until system shutdown. 

ORANGE 

(+) BRAKE 
SWITCH INPUT 
WIRE 

This wire must be connected to the vehicle’s brake light wire.  This 
wire should show +12 volts with the brakes pressed ONLY.  This 
input will shut down the remote starter if the brakes are pressed. 

EMPTY 

N/A 

NOT USED 

YELLOW 

+12 VOLT 
PARKING LIGHT 
OUTPUT 

This wire pr12 volts output and must be connected to the 
vehicle’s PARKING LIGHTS wire that tests +12 volts with the 
light switch in the ON position.  

NOTE:

 Ensure that the voltage 

does not decrease or increase when turning the dimmer control 
switch. If the voltage goes up or down, find another PARKING 
LIGHTS wire. 

 
 

Содержание PS-5565TW



















Отзывы: