background image

 

18

 
 
 
 

 

LIMITED LIFETIME WARRANTY 

 

REMOTE STARTERS: 

 
As the manufacturer, Polarstart Inc. warrants to the original consumer purchaser only (NON TRANSFERABLE), that the remote 
starter module (control box) shall be free from defects in material and workmanship, 

for as long as the original consumer

 

purchaser continuously owns the vehicle the remote starter was originally installed in

, as specified below: 

 

1)  For the first year after date of manufacture, as specified by the serial number on the module,  
Polarstart will replace the remote starter module free of charge with a new remote starter module. 
2)  For the second year after date of manufacture, as specified by the serial number on the module, Polarstart will replace the 

remote starter module free of charge with a repaired or refurbished remote starter module. 

3)  For the third and any consecutive years after the date of manufacture, as specified by the serial number on the module, 

Polarstart will provide to the original consumer purchaser a repaired or refurbished remote starter module, for a repair 
charge of $35.00. 

In all cases, the consumer must return the remote starter module to the point of purchase, and must provide an original proof of 
purchase to said retailer.  A remote starter module will be returned to the retailer for the consumer to claim within a 4 (four)-week 
period.   For case 3), a check in the amount of $35.00 must accompany the remote starter module, or the retailer may refuse the 
return. 

 
ACCESSORIES: 

 
Polarstart Inc. warrants to the original consumer purchaser that it will replace any Polarstart ACCESSORY part for a one-year period 
from date of purchase.  Accessories include all items that are not remote starter modules (such as transmitters, sirens, LED, switch, 
etc.). Accessories will only be replaced if proven defective in materials or workmanship, and if, when returned to point of purchase, 
the retailer is provided with an original proof of purchase.  The ACCESSORY will be returned to the retailer for the consumer to 
claim within a 4 (four)-week period. 
 

WARRANTY IS VOID IF: 

1) 

The product has been damaged, altered in any way, or tampered with, without the explicit written consent of an 
Polarstart technician.  For remote starter modules, this includes the opening or removal of the module’s plastic 
covering, or the removal or alteration of the barcode label on the module’s plastic covering. 

2) 

The product is damaged due to accident, fire, flood, shipping and handling, misuse, neglect, or other conditions 
beyond the control of Polarstart. 

3) 

The product has been installed or repaired by anyone other than an authorized technician. 

4) 

The product has been improperly installed or used. 

 

WARRANTY DOES NOT COVER: 

1) 

Batteries. 

2) 

Scratched or worn transmitter cases. 

3) 

Installation and / or removal charges for all remote starter modules and accessories. 

4) 

Shipping and handling charges incurred for product exchange or replacement. 

5) 

Any material damages other than to the product itself. 

 
THIS LIMITED LIFETIME WARRANTY SHALL CONSTITUTE THE SOLE LIABILITY OF POLARSTART INC. FOR OUR 
PRODUCTS, AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED. THERE ARE NO WARRANTIES 
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. NO PERSON, FIRM OR CORPORATION IS 
AUTHORIZED TO ASSUME FOR POLARSTART INC. ANY OTHER LIABILITY WITH RESPECT TO THE SALE OR USE 
OF OUR PRODUCTS. POLARSTART’S LIABILITY, WHETHER BASED ON CONTRACT, TORT, WARRANTY, STRICT 
LIABILITY, OR ANY OTHER THEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT 
FOR DAMAGE IS THE BASIS OF THE CLAIM. UNDER NO CIRCUMSTANCE WILL POLARSTART INC., ITS 
DISTRIBUTORS, OR THEIR AGENTS BEAR ANY LIABILITY WHATSOEVER FOR INCIDENTAL OR CONSEQUENTIAL 
DAMAGES. 
 

Содержание PS-5565TW



















Отзывы: