Polaris Sportsman 9921825 Скачать руководство пользователя | Manualshive

Страница: 19 / 132

background image

16

SAFETY

Safety Warnings

Stalling While Climbing a Hill

Stalling, rolling backwards or improperly
dismounting while climbing a hill could cause an
overturn.
• Always maintain a steady speed when climbing

a hill.

If all forward speed is lost:
• Keep body weight uphill.
• Apply the brakes.
• Lock the parking brake when fully stopped.
• Dismount on uphill side, or to either side if ATV is pointed straight uphill.
• Turn the ATV around and remount, following the procedure described in the

owner's manual. See page 54.

If the ATV begins rolling downhill:
• Keep body weight uphill.
• Never apply engine power.
• Never apply the rear brake while rolling backwards. Apply the single-lever

brake gradually.

• When fully stopped, apply the rear brake as well, and then lock the parking

brake.

• Dismount on uphill side, or to either side if ATV is pointed straight uphill.
• Turn the ATV around and remount, following the procedure described in the

owner's manual. See page 54.

Operating on Steep Hills

Operating on excessively steep hills could cause
an overturn.
Never operate on hills too steep for the ATV or for
your abilities. Never operate the ATV on hills
steeper than 25 degrees.

«
...
17
18
19
20
21
...
»

Содержание Sportsman 9921825





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sportsman 9921825

Бренд: E-TON Страницы: 134

Бренд: TrailMaster Страницы: 8

Бренд: TrailMaster Страницы: 40

Бренд: TrailMax Страницы: 62

Hawkeye 2X4 2007

Бренд: Polaris Страницы: 141

Бренд: Polaris Страницы: 133

RANGER 500 2017

Бренд: Polaris Страницы: 574

2010 Scrambler 4X4

Бренд: Polaris Страницы: 133

Sportsman BIG BOSS 6X6 800 EFI

Бренд: Polaris Страницы: 100

Бренд: FLEMING Страницы: 6

Sportsman 400 Lift

Бренд: Polaris Страницы: 7

Бренд: FARMA Страницы: 36

2014 SNO PRO 500

Бренд: Arctic Cat Страницы: 90

Бренд: Arctic Cat Страницы: 68

Бренд: Arctic Cat Страницы: 80

Бренд: Arctic Cat Страницы: 76

2010 1000 H2 TRV

Бренд: Arctic Cat Страницы: 104

Бренд: SILLA Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды