Polaris Sportsman 9921825 Скачать руководство пользователя | Manualshive

Страница: 83 / 132

background image

80

MAINTENANCE

Brakes

Hand Brake

The front and rear brakes are hydraulic disc brakes, activated by moving
the single brake lever toward the handlebar. These brakes are self-
adjusting.

Under normal operation, the diaphragm extends into the reservoir as
fluid level drops. If the fluid level is low and the diaphragm is not
extended, a leak is likely and the diaphragm should be replaced. To
ensure proper diaphragm operation, always fill the reservoir as needed
whenever the cover is loosened or removed. Do not overfill.

WARNING!

An over-full master cylinder may cause brake drag or brake lock-

up, which could result in serious injury or death. Maintain brake fluid at the
recommended level. Do not overfill.

The following checks are recommended to keep the brake system in
good operating condition. Check more often if brakes are used heavily
under normal operation.

1. Always keep brake fluid at an adequate

level. See page 28.

2. Check the brake system for fluid leaks.

3. Check the brakes for excessive travel or

spongy feel.

4. Check the friction pads for wear, damage

and looseness. Replace brake pads when
they are worn to 3/64" (1 mm).

5. Check the security and surface condition

of the disc.

Auxiliary Foot Brake

The hydraulic auxiliary brake system requires no adjustment. Check the
brake fluid level frequently for the auxiliary brake system. See page 30.

3/64" (1 mm)

«
...
81
82
83
84
85
...
»

Содержание Sportsman 9921825





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sportsman 9921825

2002/24 ATV-300XS

Бренд: HER CHEE Страницы: 56

Бренд: GMX MOTORBIKES Страницы: 57

Бренд: TSE Страницы: 129

Бренд: Arctic Cat Страницы: 196

Бренд: NorAM Страницы: 118

Sportsman 9920775

Бренд: Polaris Страницы: 144

Бренд: CHICAGO Страницы: 25

Бренд: Yamaha Страницы: 162

BEARTRACKER YFM250XP

Бренд: Yamaha Страницы: 163

Grizzly YFM125GW

Бренд: Yamaha Страницы: 146

Бренд: PRONAR Страницы: 150

Бренд: Ace Sports Страницы: 34

Бренд: KYMCO Страницы: 1

Бренд: U-Line Страницы: 8

Бренд: Yamaha Страницы: 169

Бренд: Yamaha Страницы: 351

1991-1993 Exciter II - 570

Бренд: Yamaha Страницы: 440

Бренд: Yamaha Страницы: 1362

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды