Polaris Sportsman 9921825 Скачать руководство пользователя

Страница: 101 / 132

MAINTENANCE

PVT System

When To Use Low Range and High Range

PVT Drying

There may be some instances when water is accidently ingested into the
PVT system. Use the following instructions to dry it out before operat-
ing.

1. Position the vehicle on a level surface.

2. Remove the drain plug. Allow the water to drain completely. Rein-

stall the drain plug.

3. Start the engine. Place the transmission in PARK.

4. Apply varying throttle for 10-15 seconds to expel the moisture and

air-dry the belt and clutches. Do not hold the throttle wide open for
more than 10 seconds.

5. Allow the engine RPM to settle to idle speed, then shift the trans-

mission to the lowest available range.

6. Test for belt slippage. If the belt slips, repeat the process.

7. Take the vehicle to your dealer for service as soon as possible.

Condition

Range to Use

Operating at speeds less than 7 MPH (11 km/h)

Low

Towing heavy loads

Low

Operating in rough terrain (swamps, mountains, etc.)

Low

Operating at speeds greater than 7 MPH (11 km/h)

High

Содержание Sportsman 9921825





































































































































Результаты поиска

Содержание Sportsman 9921825

Отзывы:

Похожие инструкции для Sportsman 9921825

Бренды по названию

Популярные бренды

Polaris Sportsman 9921825, Руководство пользователя

Результаты поиска

Содержание Sportsman 9921825

Отзывы:

Похожие инструкции для Sportsman 9921825

Бренды по названию

Популярные бренды