Polaris Sportsman 9921825 Скачать руководство пользователя | Manualshive

Страница: 112 / 132

background image

109

MAINTENANCE

Cleaning and Storage

Storage Tips

Fluid Levels

Inspect the fluid levels. Add or change fluids as recommended in the
Periodic Maintenance Chart beginning on page 62.
• Demand drive unit (front gearcase)
• ADC fluid (ADC models) (change every two years)
• Rear gearcase (if equipped)
• Transmission
• Brake fluid (change every two years and any time the fluid looks dark

or contaminated)

• Coolant (test strength/fill)

Fog the Engine

1. Support the front end of the machine so the engine is level or tilted

slightly rearward.

2. Remove the spark plug. Rotate the piston to BDC and pour two

ounces (59 ml) of Premium 4 Synthetic 0W40 engine oil into the
cylinder.

3. Reinstall the spark plug. Torque to specification.

4. Apply dielectric grease to the inside of the spark plug cap. Reinstall

the cap.

5. Turn the engine over several times using the recoil starter. Oil will

be forced in and around the piston rings and ring lands, coating the
cylinder with a protective film of fresh oil.

6. Treat the fuel system with Polaris Carbon Clean. See page 108.

7. If Polaris fuel system additive is not used, the fuel tank, fuel lines,

and carburetor should be completely drained of gasoline.

8. To eliminate any fuel remaining in the carburetor, run the engine

until it stops.

«
...
110
111
112
113
114
...
»

Содержание Sportsman 9921825





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sportsman 9921825

Бренд: Jayco Страницы: 87

Raider Extreme 1100D

Бренд: Dazon Страницы: 85

FORMULA 500 1997

Бренд: Ski-Doo Страницы: 352

Бренд: Yerf-Dog Страницы: 59

Бренд: Yamaha Страницы: 46

Бренд: Yamaha Страницы: 155

Бренд: Yamaha Страницы: 190

Бренд: OTIS Страницы: 17

Бренд: Can-Am Страницы: 127

Vyper 4WD 1100cc

Бренд: gio Страницы: 113

Бренд: Tomberlin Страницы: 151

Бренд: PRONAR Страницы: 166

Sportsman 9920364

Бренд: Polaris Страницы: 143

Бренд: Trail Rover Страницы: 38

Бренд: Landoll Страницы: 70

K2 QUAD 250 - SERVICE

Бренд: GAS GAS Страницы: 64

Бренд: Taylor-Dunn Страницы: 232

Бренд: Yamaha Страницы: 156

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды