Polaris Sportsman 9921825 Скачать руководство пользователя

Страница: 80 / 132

MAINTENANCE

Active Descent Control (ADC) Fluid

Fluid Change

1. Position the vehicle on a level surface. Before performing the fluid

change, allow the vehicle to sit for at least 30 minutes.

2. Thoroughly clean the areas around and on the ADC reservoir and

bleeder valves (one on each side of the differential).

3. Remove the reservoir cap and diaphragm assembly. Use a shop

towel or suction tool to remove debris from the fluid and reservoir.
Debris in the reservoir may result in inadequate bleeding and
reduced performance of the system.

4. Fill the reservoir to the maximum line with fresh ADC fluid.

5. Remove the protective caps from the bleeder valves.

6. Slowly loosen one of the valves (turn counter-clockwise) and allow

fluid and trapped air to flow from the fitting. Close the valve when
clean fluid begins to flow. Repeat this step for the remaining valve.

IMPORTANT:

Close the bleeder valves before the reservoir fluid level drops

below the minimum fill line. Adding fluid to an empty resevoir will result in

trapped air. If the level drops below the minimum line, add fluid to the maximum

line and repeat step 6 before proceeding.

7. Torque the valves to 80 in. lbs. (9 Nm). Reinstall the valve caps.

8. Add fresh ADC fluid to the reservoir until the level is between the

minimum and maximum marks. Make sure the reservoir is free of
debris.

9. Reinstall the cap securely.

10. Clean up any drips or spills.

Содержание Sportsman 9921825





































































































































Результаты поиска

Содержание Sportsman 9921825

Отзывы:

Похожие инструкции для Sportsman 9921825

Бренды по названию

Популярные бренды

Polaris Sportsman 9921825, Руководство пользователя

Результаты поиска

Содержание Sportsman 9921825

Отзывы:

Похожие инструкции для Sportsman 9921825

Бренды по названию

Популярные бренды