Polaris Sportsman 9921825 Скачать руководство пользователя | Manualshive

Страница: 24 / 132

background image

21

SAFETY

Safety Decals and Locations

Warning labels have been placed on the vehicle for your protection.
Read and follow the instructions on each label carefully. If any of the
labels shown in this manual differ from the labels on your vehicle,
always read and follow the instructions of the labels on the vehicle.

If an informational or graphic label becomes illegible or comes off, con-
tact your Polaris dealer to purchase a replacement. Replacement

safety

labels are provided by Polaris at no charge. The part number is printed
on the label.

General Warning/Discretionary Warning

WARNING
Improper ATV use can result in SEVERE INJURY or DEATH
ALWAYS USE AN APPROVED HELMET AND PROTECTIVE GEAR
NEVER USE ON PUBLIC ROADS
NEVER CARRY PASSENGERS
NEVER USE WITH DRUGS OR ALCOHOL

NEVER

operate:

• without proper training or instruction
• at speeds too fast for your skills or the conditions
• on public roads - a collision can occur with another vehicle
• with a passenger - passengers affect balance and steering and increase risk

of losing control

ALWAYS

:

• use proper riding techniques to avoid vehicle overturns on hills and rough

terrain and in turns

• avoid paved surfaces - pavement may seriously affect handling and control
LOCATE AND READ OPERATOR’S MANUAL.
FOLLOW ALL INSTRUCTIONS AND WARNINGS.

WARNING
• Never operate this ATV on HILLS steeper than 25 degrees

25

°

. To pre-

vent overturn on hilly terrain, use throttle and brakes gradually, and shift
weight uphill.

• REVERSE operation can be dangerous even at low speeds. Steering

becomes difficult. To prevent loss of control, avoid sudden braking or sharp
turns.

7175553

«
...
22
23
24
25
26
...
»

Содержание Sportsman 9921825





































































































































Отзывы:

Нет отзывов

Похожие инструкции для Sportsman 9921825

Бренд: Ace Sports Страницы: 79

FORMULA 500 1997

Бренд: Ski-Doo Страницы: 352

Бренд: Suzuki Страницы: 252

Бренд: Suzuki Страницы: 492

Бренд: Panther Страницы: 10

Бренд: Recon Страницы: 102

Бренд: DAELIM Страницы: 1

Бренд: JI-EE Страницы: 61

Chem-Veyor 2614D

Бренд: Walinga Страницы: 28

Бренд: KAYO MOTOR Страницы: 138

GRIZZLY 700 2013

Бренд: Yamaha Страницы: 174

POWERSPORTS FR5DGK

Бренд: MotoTec Страницы: 32

Бренд: Panther Страницы: 10

Бренд: Bosski Страницы: 12

Бренд: WilTec Страницы: 7

Бренд: Polaris Страницы: 88

Бренд: Polaris Страницы: 114

Бренд: Polaris Страницы: 107

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды