Polaris Sportsman 9921825 Скачать руководство пользователя

Страница: 115 / 132

112

ADJUSTMENTS

Camber and Caster

The camber and caster are non-adjustable.

Rear Spring

The rear shock absorber spring is adjusted
by rotating the adjuster either clockwise
or counterclockwise to increase or
decrease spring tension.

Accessory springs are available through
your Polaris dealer.

Handlebars

The handlebars can be adjusted for rider
preference.

WARNING!

Improper adjustment of the handlebars or incorrect torquing of the

adjuster block tightening bolts can cause limited steering or loosening of the
handlebars, resulting in loss of control and serious injury or death. Follow the
adjustment procedures exactly, or see your Polaris dealer for service.

1. Remove the upper headlight

pod.

2. Loosen the four handlebar

bolts.

3. Adjust the handlebar to the

desired height.

4. Be sure the handlebars do not

contact the gas tank or any
other part of the machine when
turned fully to the left or right.

5. Torque the front two bolts to

10-12 ft. lbs. (14-17 Nm), then
torque the rear two bolts. A
gap of up to 1/8" (3 mm) will
remain at the rear of the clamp
blocks.

Adjuster

Handlebar

Bolts

Содержание Sportsman 9921825





































































































































Результаты поиска

Содержание Sportsman 9921825

Отзывы:

Похожие инструкции для Sportsman 9921825

Бренды по названию

Популярные бренды

Polaris Sportsman 9921825, Руководство пользователя

Результаты поиска

Содержание Sportsman 9921825

Отзывы:

Похожие инструкции для Sportsman 9921825

Бренды по названию

Популярные бренды