Polaris Sportsman 9921825 Скачать руководство пользователя

Страница: 117 / 132

114

ADJUSTMENTS

Throttle Cable Freeplay

Adjust throttle cable freeplay at the handlebar.

1. Locate the throttle cable

adjuster at the handlebar.

2. Squeeze the end of the rub-

ber boot and slide it far
enough to expose the end of
the inline cable adjuster.

3. Loosen the adjuster lock nut.

4. Rotate the boot to turn the

adjuster until 1/16" to 1/8"
(1.5-3 mm) of freeplay is
achieved at the thumb lever.
While adjusting freeplay, be
sure to flip the throttle lever
back and forth.

5. Tighten the lock nut.

6. Squeeze the end of the rub-

ber boot and slide it over the
cable adjuster to its original
position.

Lock Nut

Adjuster

Boot

Содержание Sportsman 9921825





































































































































Результаты поиска

Содержание Sportsman 9921825

Отзывы:

Похожие инструкции для Sportsman 9921825

Бренды по названию

Популярные бренды

Polaris Sportsman 9921825, Руководство пользователя

Результаты поиска

Содержание Sportsman 9921825

Отзывы:

Похожие инструкции для Sportsman 9921825

Бренды по названию

Популярные бренды