Planex FNW-9802-T Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 51

background image

10

This chapter describes how to install the Windows95 driver for the Fast

Ethernet Adapter.

There are several varieties of Windows95, and the driver installation

procedure for this OS varies slightly among these versions. Please verify

your Windows95 version before proceeding.

1. Double click on the [My Computer] icon and double click on [Control

Panel].

2. Double click on the [System] icon.

Chapter 3

Installation under Windows95

3

1

Verifying Windows95 version

9

FNW-9802-T

●

To ensure 100Mbps network operation, Category 5 UTP cabling is

required.

●

For 10Mbps network operation, use Category 3 or higher UTP cable.

●

To connect the Adapter to a hub, the cable must be "straight" type UTP

cable (e.g. PLANEX UTP-xx-05 and UTP-xx-DT).

●

To connect two computers directly without using a hub, use a "crossover"

cable (e.g. PLANEX UTP-xx-05CR).

2

3

About Network Cables

«
...
9
10
11
12
13
...
»

Содержание FNW-9802-T




















































Отзывы:

Нет отзывов

Похожие инструкции для FNW-9802-T

Wireless Router

Бренд: Watchguard Страницы: 11

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 28

Бренд: D-Link Страницы: 48

Бренд: D-Link Страницы: 83

Бренд: D-Link Страницы: 155

Бренд: IBM Страницы: 248

Бренд: Qlogic Страницы: 2

Бренд: Qlogic Страницы: 172

Бренд: Ubiquiti Страницы: 3

8677 - BladeCenter Rack-mountable - Power Supply

Бренд: IBM Страницы: 126

Бренд: Abocom Страницы: 63

Бренд: ZyXEL Communications Страницы: 2

Бренд: Telestar Страницы: 16

Бренд: NetCommWireless Страницы: 28

Бренд: R.V.R. Elettronica Страницы: 171

VAR-SOM-MX6 HEAT PLATE KIT

Бренд: Variscite Страницы: 3

Internet Security Appliances

Бренд: SonicWALL Страницы: 293

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды