Planet Networking & Communication FRT-415N Скачать руководство пользователя

Страница: 67 / 117

User Manual of FRT-415N

Periodic Inform Enable

Select

Enable

to periodically connect to the ACS to check whether the

configuration updates.

Periodic Inform Interval

Specify the amount of time between connections to ACS.

Connection Request

User Name

The connection username provided by TR-069 service.

Password

The connection password provided by TR-069 service.

Debug

Show Message

Select

Enable

to display ACS SOAP messages on the serial console.

CPE sends GetRPC

Select

Enable

to enable the router to contact the ACS to obtain

configuration updates.

Skip MReboot

Specify whether to send an MReboot event code in the inform
message.

Delay

Specify whether to start the TR-069 program after a short delay.

Auto-Execution

Specify whether to automatically start the TR-069 after the router is
powered on.

Содержание FRT-415N






















































































































Результаты поиска

Содержание FRT-415N

Отзывы:

Похожие инструкции для FRT-415N

Бренды по названию

Популярные бренды

Planet Networking & Communication FRT-415N, Руководство пользователя

Результаты поиска

Содержание FRT-415N

Отзывы:

Похожие инструкции для FRT-415N

Бренды по названию

Популярные бренды