Planet Networking & Communication FRT-415N Скачать руководство пользователя страница 54

Страница: 54 / 117

User Manual of FRT-415N

5.4.1.1 Static Route

Click

Static Route

in the left pane and the page shown in the following figure appears. This page is used to

configure the routing information. You can add or delete IP routes.

Figure 5-33

Static Route

The following table describes the parameters:

Field

Description

Enable

Click it to enable/disable the selected route or route to be added.

Destination

The network IP address of the subnet. The destination can be specified

as the IP address of a subnet or a specific host in the subnet. It can also

be specified as all zeros to indicate that this route should be used for all

destinations for which no other route is defined (this is the route that

creates the default gateway).

Subnet Mask

The network mask of the destination subnet.

Next Hop

The IP address of the next hop through which traffic will flow towards the

destination subnet.

Metric

Defines the number of hops between network nodes that data packets

travel.

Interface

The WAN interface to which a static routing subnet is to be applied.

Add Route

Add a user-defined destination route.

Update

Update the selected destination route on the Static Route Table.

Содержание FRT-415N






















































































































Результаты поиска

Содержание FRT-415N

Отзывы:

Бренды по названию

Популярные бренды

Planet Networking & Communication FRT-415N, Руководство пользователя

Результаты поиска

Содержание FRT-415N

Отзывы:

Бренды по названию

Популярные бренды