Planet Networking & Communication FRT-415N Скачать руководство пользователя | Manualshive

Страница: 68 / 117

background image

User Manual of FRT-415N

68

5.4.5 Port Mapping

The FRT-415N provides multiple interface groups. Up to five interface groups are supported including one default
group. The LAN and WAN interfaces could be included. Traffic coming from one interface of a group can only be
flowed to the interfaces in the same interface group. Thus, the FRT-415N can isolate traffic from group to group for
some applications. By default, all the interfaces (LAN and WAN) belong to the default group, and the other four
groups are all empty. It is possible to assign any interface to any group but only one group.

Figure 5-47

Port Mapping

The following table describes the parameters:

Field

Description

Enabled/Disabled

Click the

radio

button to enable/disable the interface group feature. If

disabled, all interfaces belong to the default group.

Interface groups

To manipulate a mapping group:
1. Select a group from the table.
2. Select interfaces from the available/grouped interface list and add it
to the grouped/available interface list using the arrow buttons to
manipulate the required mapping of the ports.

«
...
66
67
68
69
70
...
»

Содержание FRT-415N






















































































































Отзывы:

Нет отзывов

Похожие инструкции для FRT-415N

LTE Mobile HotSpot PRO

Бренд: Samsung Страницы: 77

Бренд: macaroon Страницы: 13

RouterBOARD 750

Бренд: MikroTik Страницы: 2

Бренд: UniFi Страницы: 22

Бренд: Modecom Страницы: 48

Бренд: ARGtek Страницы: 14

Бренд: Azio Страницы: 209

Бренд: Marley Страницы: 24

Бренд: Marley Страницы: 25

Бренд: EnGenius Страницы: 2

Бренд: EnGenius Страницы: 64

Бренд: AmbiCom Страницы: 6

Бренд: PHICOMM Страницы: 53

Бренд: q-Tech Страницы: 12

Road Runner Mobile

Бренд: Sierra Wireless Страницы: 9

Бренд: Sierra Wireless Страницы: 11

Бренд: Spectrum Страницы: 2

StarHub MAX-STREAM EA8100

Бренд: Linksys Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды