manualshive.com logo in svg

Planet Networking & Communication FRT-415N, Руководство пользователя

Поделиться
Скачать
Planet Networking & Communication FRT-415N Скачать руководство пользователя страница 75

User Manual of FRT-415N 

 

 

75

Query Interval 

The amount of time between IGMP General Query messages sent by 
the router (if the router is a querier on this subnet). 

Query Response Interval

The maximum amount of time in seconds that the IGMP router waits to 
receive a response to a General Query message. The query response 
interval is the Maximum Response Time field in the IGMP v2 Host 
Membership Query message header. The default query response 
interval is 10 seconds and must be less than the query interval. 

Group Leave Delay 

The amount of time in seconds that the IGMP router waits to receive a 
response to a Group-Specific Query message. The last member query 
interval is also the amount of time in seconds between successive 
Group-Specific Query messages. 

 

 

5.5.1.2 MLD 

MLD means Multicast Listener Discovery -- its component of the IPv6. MLD is used by IPv6 routers for 
discovering multicast listeners on a directly-attached link, much like IGMP being used in IPv4. 

 

Figure 5-55 

MLD 

 

The following table describes the parameters: 

Field 

Description 

MLD Proxy 

MLD Proxy can be used to support IPv6 multicast data. Enable/Disable 
the function to access. 

MLD Snooping 

Snooping is an IPv6 multicast constraining mechanism that runs on 
Layer 2 devices to manage and control IPv6 multicast groups. By 
analyzing received MLD messages, a Layer 2 device running MLD 
Snooping establishes mappings between ports and multicast MAC 

Содержание FRT-415N






















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды