Advanced Operations
39
<DRB1388> En
English
Loop playback
★
This function is not supported when the rear panel mode select
switch (MODE NORMAL/DJ) is set to the NORMAL position.
■
To create a loop
1. Press the PLAY/PAUSE (
3
/
8
) button to begin playback.
2. During playback, press the LOOP IN/REALTIME CUE but-
ton.
¶
This step is unnecessary if you wish to use a previously recorded
cue point as the loop-in point.
¶
During the time required for writing the loop-in point, the
LOOP
IN/REALTIME CUE
button will flash for about 2 seconds.
3. During playback, press the LOOP OUT/OUT ADJUST but-
ton at the point you wish to use as the loop-out point.
¶
Repeat play (loop play) will begin without break between the se-
lected loop-in and loop-out points.
¶
The frame search function can be used to set more accurate out
points.
¶
If an alternate viewing angle or audio channel is selected before
setting a loop-out point, it may not possible to designate a loop-
out point.
¶
Loop-out points cannot be set during reverse play.
¶
In the case of MP3, looping is possible only within the same track
where the cue point was set.
■
To cancel loop play
During loop playback, press the RELOOP/EXIT button.
¶
The loop will be canceled and playback will continue normally past
the loop-out point.
■
To change a loop-out point
1. During loop playback, press the LOOP OUT/OUT ADJUST
button.
¶
The display will show the loop-out point time, and the
LOOP OUT/
OUT ADJUST
button will flash rapidly, while the
LOOP IN/
REALTIME CUE
button indicator turns off.
2. Press the manual search buttons (REV
1
, FWD
¡
) or
rotate the jog dial.
¶
The loop-out point will change in one-frame units.
¶
The loop-out point cannot be moved to a location before the loop-
in point.
¶
To cancel the adjust mode and return to loop play, press the
LOOP
OUT/OUT ADJUST
button or wait 30 seconds.
¶
The loop-out point cannot be adjusted during reverse play.
¶
In the case of MP3, the loop-out point can be adjusted only within
the same track where the cue point was set.
MODE
NORMAL/DJ
REV
1
,
FWD
¡
LOOP IN/
REALTIME
CUE
PLAY/PAUSE
6
DIRECTION
FWD/REV
EMERGENCY LOOP
LOOP OUT/
OUT ADJUST
RELOOP/
EXIT
Jog dial
■
To return to a loop (reloop)
After cancellation of a loop, press the RELOOP/EXIT button
during normal playback.
¶
Playback will return to the loop-in point of the previously set loop, and
loop play will resume.
¶
In the case of MP3, reloop can be performed only within the same
folder.
■
Automatic loop-out setting
4-beat loop (emergency loop)
During playback, press the EMERGENCY LOOP button.
¶
The normal loop playback indicators will appear (flashing
LOOP OUT/
OUT ADJUST
button and
LOOP IN/REALTIME CUE
button), and
the
EMERGENCY LOOP
indicator will flash.
¶
The point at which the button is pressed will become the loop-in point,
and a loop-out point will be set automatically as described below;
loop playback will then continue between the two points.
· If the immediately preceding BPM value is known, a point four beats
afterwards will become the loop-out point.
· If the immediately preceding BPM value is not known, the loop-out
point will be set four seconds after the loop-in point.
· If either of the above two conditions come after the track end, the
track end will be made the loop-out point.
¶
When the
EXIT/RELOOP
button is pressed, the loop play will end
and normal playback will resume.
¶
Emergency loop is not supported during reverse play.
1-track loop (chapter/track repeat)
During playback, hold the EMERGENCY LOOP button de-
pressed for 1 second or more.
When the
EMERGENCY LOOP
button is held depressed for 1 second or
more during playback, 1-track loop is enabled, thus repeating playback of
the currently playing chapter or track.
¶
The indicator “
CHP LOOP
” (during DVD playback) or “
TRK LOOP
”
(during CD or MP3 playback) will appear in the display, and the unit
will search to the beginning of the currently playing chapter or track,
and set the loop-in point there.
¶
The normal loop playback indicators (
LOOP OUT/OUT ADJUST
and
LOOP IN/REALTIME CUE
buttons) will flash, and the chapter end or
track end will be automatically set at the loop-out points and playback
will resume.
¶
If the
EXIT/RELOOP
button is pressed, the loop play will be canceled
and normal playback will resume.
¶
Chapter/track repeat cannot be designated during reverse playback.
¶
When recording to a memory card, record after playing the track to
the end.
Reverse play
★
This function is not supported when the rear panel mode select
switch (MODE NORMAL/DJ) is set to the NORMAL position.
Set the DIRECTION FWD/REV select switch to the REV posi-
tion (forward).
The
REV
indicator lights and playback occurs in reverse.
¶
The jog dial’s operation to accelerate/decelerate playback is reversed.
¶
During reverse playback, loop points cannot be set nor loop-out points
modified.
¶
When track search or loop play are performed, the jog dial’s audio/
video memory status display will flash for 1-2 seconds and scratch/
reverse operations may not respond.
About fader start play
★
This function is not supported when the rear panel mode select
switch (MODE NORMAL/DJ) is set to the NORMAL position.
When the supplied accessory control cord is used to connect the CON-
TROL connector of this player to the CONTROL connector of a DJ mixer
DJM-300, DJM-500, DJM-600, DJM-3000, DJM-909, or DJM-707, rais-
ing the DJ mixer’s channel fader lever simultaneously releases the player
from cue standby, automatically starting instant playback. Fader start
can also be started by using the cross fader operation; when the fader
lever is returned to its original position, the player also returns to its cue
point (back cue) and enters cue standby. (For connection instructions
consult page 13).
