manualshive.com logo in svg

PIAGGIO Liberty 50 Catalyzed, Руководство по ремонту

Поделиться
Скачать
PIAGGIO Liberty 50 Catalyzed Скачать руководство пользователя страница 89

Remove the tube passage seal from the crank-

case shown in the figure

Refitting

To refit, perform the steps in the reverse direction

to disassembly

Remember to drain after refitting using the screw

shown in the figure

Fuel supply

- Disconnect the fuel supply and the suction taking

pipe from the carburettor.

- Check that there are no fuel leaks between the

two tubes.

- Close the fuel outlet pipe.

- By means of the MITYVAC pump apply 0.1 bar

of suction to the tap.

- Make sure that the suction is kept stable and that

and that there are no fuel leaks.

- Reconnect the vacuum pipe to the manifold.

- Position the fuel pipe with the outlet at the point

of the tap.

- Turn the engine by using the starter motor for five

seconds with the carburettor at minimum.

- Take up the fuel by means of a graded burette.

N.B.

THE MEASUREMENT MAY BE FALSIFIED BY THE INCOR-
RECT NUMBER OF REVS OR BY THE WRONG POSITION

Liberty 50 Catalyzed

Engine

ENG - 89

Содержание Liberty 50 Catalyzed






































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды